View source for MQ2 Smoke Detector Shield for Arduino

== Introduction  ==


MQ2  flammable gas and smoke sensor detects the concentrations of combustible gas in the air and ouputs its reading as an analog voltage. The sensor can measure concentrations of flammable gas of 300 to 10,000 ppm.The sensor can operate at temperatures from -20 to 50°C and consumes less than 150 mA at 5 V.



Connecting five volts across the heating (H) pins keeps the sensor hot enough to function correctly. Connecting five volts at either the A or B pins causes the sensor to emit an analog voltage on the other pins. A resistive load between the output pins and ground sets the sensitivity of the detector. Please note that the picture in the datasheet for the top configuration is wrong. Both configurations have the same pinout consistent with the bottom configuration.The resistive load should be calibrated for your particular application using the equations in the datasheet, but a good starting value for the resistor is 20 kΩ.

[[File:N98DG WITHOUT PACKAGED FRONT.jpg | 640px]]

[[File:N98DG WITHOUT PACKAGED BACK.jpg|640px]]

Below photos are for shields without headers:

[[File:MQ2 Smoke Detector Shield for Arduino 001.jpg|640px]]

[[File:MQ2 Smoke Detector Shield for Arduino 002.jpg|640px]]

[[File:MQ2 Smoke Detector Shield for Arduino 003.jpg|640px]]

== Features  ==





== Application Ideas  ==





== Cautions  ==





== Schematic  ==

*[https://s3.amazonaws.com/linksprite/Shields/MQ2/MQ2_schematics.pdf Schematics]

== Specification  ==





== Pin definition and Rating  ==





== Mechanic Dimensions  ==





== Usage  ==





=== Hardware Installation  ===





=== Programming  ===

Sample Program


<syntaxhighlight lang="c">

/* Sample Arduino for MQ2 Smoke Sensor Shield
   05/03/2011
**********************************************/
const int analogInPin = A0;  // Analog input pin that the potentiometer is attached to
const int analogOutPin = 9; // Analog output pin that the LED is attached to

int sensorValue = 0;        // value read from the pot
int outputValue = 0;        // value output to the PWM (analog out)
float thickness;
int count,count1;

void setup() {
  // initialize serial communications at 9600 bps:
  Serial.begin(9600); 
  pinMode(7, OUTPUT);  
}

void loop() {
  
  count1++;
  // read the analog in value:
  sensorValue = analogRead(analogInPin);            
  // map it to the range of the analog out:
  outputValue = map(sensorValue, 0, 1023, 0, 255);  
  // change the analog out value:
  analogWrite(analogOutPin, outputValue);           

  if(count1==30)
  {
    count1=0;
    // print the results to the serial monitor:
    Serial.print("sensor = " );                       
    Serial.print(sensorValue);      
    Serial.print("\t output = ");      
    Serial.println(outputValue);
  
    thickness = 20000-(5000*(1023/(float)sensorValue)-1);         //This relationship is wrong,According to demand, own calculations relationship

    Serial.print("thicknes = ");
    Serial.println( thickness);
  }
  count++;
  if(count>=(255-outputValue))
  {
    count=0;
  }
  if(count < (255-outputValue)/2)
  { 
    digitalWrite(7, HIGH);   // set the LED on
    delay(20);
  }
 // delay(1023-sensorValue);   
  else
  {
    digitalWrite(7, LOW);    // set the LED off
    delay(20);
  }

 // delay(1023-sensorValue);                         
}

</syntaxhighlight>

== FAQ  ==
Please list your question here:

== Support  ==

If you have questions or other better design ideas, you can go to our [http://www.linksprite.com/forum/index.php forum] to discuss or creat a ticket for your issue at [http://www.linksprite.com/support/ linksprite support].

== Resources  ==


*[https://s3.amazonaws.com/linksprite/Shields/MQ2/MQ2.pdf MQ2 Datasheet]
*[https://s3.amazonaws.com/linksprite/MQ-2/TECHNICAL+DATA+MQ-2+GAS+SENSOR.pdf TECHNICAL DATA MQ-2 GAS SENSOR]

== How to buy  ==

You can order from [http://store.linksprite.com/mq2-smoke-detector-shield-for-arduino-pcduino/ LinkSprite Store] or [http://www.cutedigi.com/arduino-shields/mq2-smoke-detector-shield-for-arduino.html  CuteDigi].

== See Also  ==

Other related products and resources.

== Licensing  ==

This documentation is licensed under the Creative Commons [http://creativecommons.org/licenses/by-sa/3.0/ Attribution-ShareAlike License 3.0] Source code and libraries are licensed under [http://www.gnu.org/licenses/gpl.html GPL/LGPL], see source code files for details.