10mm Green LED Module - Revision history

Alvin: /* Introduction */

2016-07-18T10:07:17Z

‎Introduction

2016-07-18T10:06:02Z

‎Introduction

2016-07-18T10:04:43Z

‎Introduction

2014-06-12T05:42:15Z

‎Features

2014-06-10T02:58:16Z

‎Schematics

2014-04-15T08:19:41Z

2014-04-08T04:58:38Z

2013-04-25T12:55:51Z

2013-04-25T12:55:04Z

2013-03-14T00:57:04Z

@@ Line 5: / Line 5: @@
-[[File:10mm Green LED 118101001-11 first.jpg| 640px]]
+[[File:10mm Green LED 118101001-11 first.jpg| 400px]]
-[[File:10mm Green LED 118101001-11 second.jpg| 640px]]
+[[File:10mm Green LED 118101001-11 second.jpg| 400px]]
 == Features ==

← Older revision		Revision as of 10:06, 18 July 2016
Line 6:		Line 6:

	[[File:10mm Green LED 118101001-11 first.jpg\| 640px]]		[[File:10mm Green LED 118101001-11 first.jpg\| 640px]]
		+
		+
		+	[[File:10mm Green LED 118101001-11 second.jpg\| 640px]]

	== Features ==		== Features ==

@@ Line 3: / Line 3: @@
 Linker LED Module is designed for the beginners of Arduino/pcDuino to monitor controls from digital ports. It can be mounted to the surface of your box or desk easily and used as pilot lamp for power or signal. Its brightness can be adjust by potentiometer.
-[[File:LED10MM G.jpg | 400px]]
 == Features ==

@@ Line 7: / Line 7: @@
 == Features ==
-Dimensions: 25.5×24.5×23.5mm
+Dimensions: 20.4×24.2×21.0mm
 Net weight: 3g
 == Schematics ==

@@ Line 1: / Line 1: @@
 [[File:LED10MM G.jpg | 400px]]
-== Sample ==
+*[https://s3.amazonaws.com/linksprite/LinkerKit/Linker_LED.pdf Schematics]
 <syntaxhighlight lang="c">
 /*
-   grove Relay
+   Blink
-   the LED will slowly blink
+   Turns on an LED on for one second, then off for one second, repeatedly.
    This example code is in the public domain.
   */
 void setup() {
    // initialize the digital pin as an output.
-  // Pin 13 has an LED connected on most Arduino boards:
+   pinMode(13, OUTPUT);
+}
 void loop() {
-   digitalWrite(RelayControlPin, HIGH);   // set the LED on
+   digitalWrite(13, HIGH);   // set the LED on
-   delay(500);              // wait for a second
+   delay(1000);              // wait for a second
-   digitalWrite(RelayControlPin, LOW);    // set the LED off
+   digitalWrite(13, LOW);    // set the LED off
-   delay(500);              // wait for a second
+   delay(1000);              // wait for a second
+}
 </syntaxhighlight>

← Older revision		Revision as of 12:55, 25 April 2013
Line 2:		Line 2:

	[[File:LED10MM G.jpg \| 400px]]		[[File:LED10MM G.jpg \| 400px]]
		+
		+
		+	== Sample ==
		+
		+	/*
		+	grove Relay
		+	the LED will slowly blink
		+
		+	This example code is in the public domain.
		+	*/
		+
		+	int RelayControlPin = 13;
		+	void setup() {
		+	// initialize the digital pin as an output.
		+	// Pin 13 has an LED connected on most Arduino boards:
		+	pinMode(RelayControlPin, OUTPUT);
		+	}
		+
		+	void loop() {
		+	digitalWrite(RelayControlPin, HIGH); // set the LED on
		+	delay(500); // wait for a second
		+	digitalWrite(RelayControlPin, LOW); // set the LED off
		+	delay(500); // wait for a second
		+	}