Bluetooth Shield for Arduino - Revision history

Alvin at 07:06, 16 September 2015

2015-09-16T07:06:42Z

2015-09-07T02:11:17Z

‎Introduction

2014-02-18T07:04:24Z

2013-05-28T03:32:41Z

2013-05-25T22:42:46Z

‎Bluetooth shield communicates to Android Smartphone

2013-05-25T22:41:18Z

‎Bluetooth shield communicates to Android Smartphone

2013-05-25T22:39:10Z

‎Bluetooth shield communicates to Android Smartphone

2013-05-25T22:37:53Z

‎Bluetooth shield communicates to Android Smartphone

2013-05-25T22:36:13Z

‎Bluetooth shield communicates to Android Smartphone

2013-05-25T22:35:00Z

‎Bluetooth shield communicates to Android Smartphone

← Older revision		Revision as of 07:06, 16 September 2015
Line 10:		Line 10:
	[[File:N97DG WITHOUT PACKAGED BACK.jpg\|640px]]		[[File:N97DG WITHOUT PACKAGED BACK.jpg\|640px]]

−	~~[[File:N97DG PACKAGED FRONT.jpg\|640px]]~~

−	~~[[File:N97DG PACKAGED BACK.jpg\|640px]]~~

	== Features ==		== Features ==

@@ Line 6: / Line 6: @@
 '''Note''': The Shield may not be compatible with some Bluetooth capable devices, like some HTC mobile phone (G7 with Android 2.33) and Apple devices with special profile on Bluetooth function.<br>
-[[File:bluetooth shield.jpg | 400px]]
+[[File:N97DG WITHOUT PACKAGED FRONT.jpg | 640px]]
 == Features  ==

← Older revision		Revision as of 07:04, 18 February 2014
Line 410:		Line 410:

	:Search for device "LinkSprite". The pairing pin is '1234'.		:Search for device "LinkSprite". The pairing pin is '1234'.
		+
		+	== How to buy ==
		+	Here to buy Bluetooth Shield for Arduino on [http://store.linksprite.com/linksprite-bluetooth-shield-for-arduino/ store]

@@ Line 16: / Line 16: @@
 *A full set of configuration commands
 *On board PCB Antenna
 == Specification ==

← Older revision		Revision as of 22:42, 25 May 2013
Line 401:		Line 401:
	[[File:Bluetoothshield android 1.jpg]]		[[File:Bluetoothshield android 1.jpg]]
	: Now we move the mode selection swtich to 'NC', and send upper case 'S' so that the Bluetooth module enter into normal working mode, and LED D1 will start to blink at a period of 0.4 seconds. That means the bluetooth shield initiated successfully.		: Now we move the mode selection swtich to 'NC', and send upper case 'S' so that the Bluetooth module enter into normal working mode, and LED D1 will start to blink at a period of 0.4 seconds. That means the bluetooth shield initiated successfully.
		+
		+	[[File:Bluetoothshield android 2.jpg]]
		+
		+	:Download a Bluetooth serial port app (for Andoird) and install on Android smartphone with bluetooth function.
		+
		+	:Search for device "LinkSprite". The pairing pin is '1234'.

← Older revision		Revision as of 22:41, 25 May 2013
Line 400:		Line 400:

	[[File:Bluetoothshield android 1.jpg]]		[[File:Bluetoothshield android 1.jpg]]
		+	: Now we move the mode selection swtich to 'NC', and send upper case 'S' so that the Bluetooth module enter into normal working mode, and LED D1 will start to blink at a period of 0.4 seconds. That means the bluetooth shield initiated successfully.

← Older revision		Revision as of 22:39, 25 May 2013
Line 398:		Line 398:
	</syntaxhighlight>		</syntaxhighlight>
	: Launch X-CTU to open the COM port, configure the baud rate to be 38400/0/8/N/1. LED-D1 on Bluetooth shield will start to blink at a period of 2 seconds. At the same time, we will see the following output on serial port:		: Launch X-CTU to open the COM port, configure the baud rate to be 38400/0/8/N/1. LED-D1 on Bluetooth shield will start to blink at a period of 2 seconds. At the same time, we will see the following output on serial port:
		+
		+	[[File:Bluetoothshield android 1.jpg]]

← Older revision		Revision as of 22:37, 25 May 2013
Line 397:		Line 397:

	</syntaxhighlight>		</syntaxhighlight>
−	: Launch X-CTU to open the COM port, the baud rate ~~setting is~~	+	: Launch X-CTU to open the COM port, configure the baud rate to be 38400/0/8/N/1. LED-D1 on Bluetooth shield will start to blink at a period of 2 seconds. At the same time, we will see the following output on serial port:

← Older revision		Revision as of 22:36, 25 May 2013
Line 397:		Line 397:

	</syntaxhighlight>		</syntaxhighlight>
		+	: Launch X-CTU to open the COM port, the baud rate setting is

@@ Line 314: / Line 314: @@
 :Copy and paste the following sample code and download to Arduino:
 #include <SoftwareSerial.h>
@@ Line 394: / Line 395: @@
+     }
+}