DSO 068 DIY kit - Revision history

Alvin: /* Supporting Documents and Tools: */

2016-07-08T06:47:50Z

‎Supporting Documents and Tools:

Alvin: /* Product Documents and firmwares */

2016-07-08T06:45:22Z

‎Product Documents and firmwares

Alvin: /* Product Documents and firmwares: */

2016-07-07T11:50:11Z

‎Product Documents and firmwares:

Alvin: /* Ordering Info */

2016-07-07T11:41:11Z

‎Ordering Info

Alvin: Created page with "== Introduction == DSO 068 DIY kit uses through-hole components as much as it can. This makes the scope unique among peers. With through-hole components the kit eases off th..."

2016-07-07T11:29:03Z

Created page with "== Introduction == DSO 068 DIY kit uses through-hole components as much as it can. This makes the scope unique among peers. With through-hole components the kit eases off th..."

New page

== Introduction ==

DSO 068 DIY kit uses through-hole components as much as it can. This makes the scope unique among peers. With through-hole components the kit eases off the requirement of assembly skills and at the same time allows deeper user involvement. Most importantly it brings in the freedom for users to test, modify, experiment, and even design their own projects. And this means more fun!

More over, DSO 068 is not just a kit for training but also a practical tool for everyday use. It was designed on the base of DSO 062 kit and comprises many enhancements in hardware and firmware. Major improvements include:

*Higher sensitivity (10mV/div vs 100mV/div)
*Wider analog bandwidth (3MHz vs 1MHz)
*Larger capture buffer (1024 points vs 256 points)
*Variable trigger position (1% - 100%) with indicator
*Test signal generator with variable frequency and amplitude
*USB connection
*Upload of captured raw data as CSV file [ Example ]
*Work as USB scope (with jyeLab) and data logger (8 channels, 10-bit resolution)
*Higher sensitivity (0.2Vpp vs 3Vpp) in built-in frequecy meter
*Battery/USB powered
*Fully enclosured

[[File:DSO068-1.jpg]]

== See chart: DSO068 vs DSO062. ==

Operations of DSO 068 are even easier thanks to silicone pushbuttons and rotary encoder. Parameter setting is simply, straightforward, and quick. Mode switch and utilities are driven by menu. Absolutely no complicate navigation.

This kit is particularly suitable for educational use. It is a great tool for college students.

== Contents ==

The DSO 068 Kit consists of the following major parts:

*Main circuit board with pre-soldered ICs and a few SMD parts. Board is pre-tested and MCUs on board are pre-programmed.
*128 X 64 graphic dot-matrix LCD module.
*Step-up voltage converter board (JYE116). It boosts battery voltage to 5V from as low as 2V.
*Voltage inverter board (JYE120). It generates -5V form +5V with current capacity up to 200mA.
*On/Off switch board (JYE117). This is the power switch of instrument. [optional]
*Li-ion battery charger board (JYE118). It includes the USB/Battery power switch circuit. [optional]
*USB-Uart converter board (JYE119). This bridges the scope to USB host. [optional]
*Professional 20MHz probe with selectable 1X/10X attenuation.
*Enclosure set including stand, switch caps, etc.
*All through-hole components, mechanical parts, and accessaries.

Shipment of kit also includes color-printed Assembly Guide and User Manual. All other documents can be downloaded at this page. It is suggested that users also download the softcopies of the accompanying documents for enlargement to have better viewing on screen.

'''NOTE:''' Battery is not included in standard product configuration and need to purchase separately. Shipments containing battery could incur higher shipping cost and longer delay due to restrictions of shipping agents.

Source codes of student version firmware are also provided for downloading. They are simplified from full version to help users to understand how the oscilloscope works. The sampling rate of student version is limited to 500Sa/s - 100KSa/s with no other features.

== Ordering Info ==

[[File:DSO068 .jpg]]

== Product Documents and firmwares: ==

*Users Manual
*Assembly Guide [For F version PCB]
*Assembly Guide [For H version PCB]
*Schematic [F version]
*Schematic [H version]
*Firmwares
*Source codes of Learning Edition
*Capture Uploading and Waveform File Format
*Data Interface of DSO 068

== Supporting Documents and Tools: ==

*How to Calibrate 10X Probe
*How to Upgrade Firmware by Bootloader
*Powering JYE Tech Oscilloscopes With Cellphone Batteries
*Windows application for upgrading firmware via bootloader
*Virtual COM Port driver (for Uart - USB bridge CP210X)

== Specification ==

=== Vertical ===

*Number of Channel: 1
*Analog Bandwidth: 0 - 3MHz
*Sensitivity: 10mV/Div -- 5V/Div
*Resolution: 8-bit
*Input Impedance: 1M ohm
*Maximum Input voltage: 50Vpk (for 1X probe) and 400Vpk (for 10X probe)
*Coupling: DC, AC, GND

=== Horizontal ===

*Max Real-time Sampling Rate: 2MSps
*Max Equivalent-Time Sampling Rate: 20MSps
*Timebase: 0.5us/Div - 10m(minute)/Div
*Record Length: 256, 512, and 1024 variable
*Run/Hold Modes: one button switchable

=== Trigger ===

*Trigger Modes: Auto, Normal, Single
*Trigger Types: Rising/falling edge
*Trigger Position: 0% - 100% of capture buffer adjustable
*Trig Point Indicator: Yes

=== Test Signal Generator ===

*Frequency adjustable from 1Hz - 100KHz (41 frequencies)
*Amplitude adjustable among 0.3V, 1V, 3V, and 5V

=== Other Features ===

*Save captured waveform to EEPROM and recall after power outage
*Upload screen display as bitmap file
*Upload waveform as CSV file
*USB connection for data transfer and firmware upgrade
*Rotary encoder for quick parameter setting

=== Display ===

*2-inch 128 X 64 black-and-white dot-matrix LCD
*Backlight ON/OFF control
*Contrast adjustable

=== Power Supply ===

*3.7V Li-ion battery/USB
*Supply Current: 300mA @ 3.7V(LCD backlight ON, typical).
*Built-in charger

=== Physical ===

*Dimension: 140mm X 70mm X 30mm
*Weight: 120 gram (not including battery and probe)

@@ Line 52: / Line 52: @@
 [[File:DSO068.jpg]]
-== Product Documents and firmwares: ==
+== Product Documents and firmwares ==
 *Users Manual

@@ Line 66: / Line 66: @@
 == Supporting Documents and Tools: ==
-*How to Calibrate 10X Probe
+*[https://s3.amazonaws.com/linksprite/DSO068/HowToCalibrate10xProbe+A.pdf How to Calibrate 10X Probe]
-*How to Upgrade Firmware by Bootloader
+*[https://s3.amazonaws.com/linksprite/DSO068/HowToUpgradefirmwareByBootloader+B.pdf How to Upgrade Firmware by Bootloader]
-*Powering JYE Tech Oscilloscopes With Cellphone Batteries
+*[https://s3.amazonaws.com/linksprite/DSO068/PoweringJYEtechOscilloscopesWithCellphoneBattery+C.pdf Powering JYE Tech Oscilloscopes With Cellphone Batteries]
-*Windows application for upgrading firmware via bootloader
+*[https://s3.amazonaws.com/linksprite/DSO068/avrubd+D.rar Windows application for upgrading firmware via bootloader]
-*Virtual COM Port driver (for Uart - USB bridge CP210X)
+*[https://s3.amazonaws.com/linksprite/DSO068/CP210x_VCP_Win_XP_S2K3_Vista_7+(1)+E.zip Virtual COM Port driver (for Uart - USB bridge CP210X)]
 == Specification ==

@@ Line 54: / Line 54: @@
 == Product Documents and firmwares ==
-*Users Manual
+*[https://s3.amazonaws.com/linksprite/DSO068/UserManual_068+1.pdf Users Manual]
-*Assembly Guide [For F version PCB]
+*[https://s3.amazonaws.com/linksprite/DSO068/AssemblyGuide_068F+2.pdf Assembly Guide [For F version PCB]
-*Assembly Guide [For H version PCB]
+*[https://s3.amazonaws.com/linksprite/DSO068/AssemblyGuide_068H+3.pdf Assembly Guide [For H version PCB]
-*Schematic [F version]
+*[https://s3.amazonaws.com/linksprite/DSO068/Schematic_068F+4.pdf Schematic [F version]]
-*Schematic [H version]
+*[https://s3.amazonaws.com/linksprite/DSO068/Schematic_068H+5.pdf Schematic [H version]]
 *Firmwares
-*Source codes of Learning Edition
+*[https://s3.amazonaws.com/linksprite/DSO068/068(LE)_SourceCodes+7.rar Source codes of Learning Edition]
-*Capture Uploading and Waveform File Format
+*[https://s3.amazonaws.com/linksprite/DSO068/CaptureUploadingAndWaveformFileFormat+8.pdf Capture Uploading and Waveform File Format]
-*Data Interface of DSO 068
+*[https://s3.amazonaws.com/linksprite/DSO068/TheDataInterface_068+9.pdf Data Interface of DSO 068]
 == Supporting Documents and Tools: ==

@@ Line 50: / Line 50: @@
 == Ordering Info ==
-[[File:DSO068 .jpg]]
+[[File:DSO068.jpg]]
 == Product Documents and firmwares: ==