LinkSprite Extension Plate for Clear Enclosure for Arduino - Revision history

Alvin at 09:14, 20 February 2014

2014-02-20T09:14:07Z

2013-04-07T07:08:01Z

2013-04-07T04:48:54Z

2013-01-10T10:00:36Z

‎Usage

2013-01-10T09:55:07Z

‎Introduction

2013-01-10T09:49:40Z

‎Usage

2013-01-10T09:46:11Z

‎Usage

2013-01-10T09:45:40Z

‎Usage

2013-01-10T09:19:26Z

2013-01-09T09:58:34Z

@@ Line 1: / Line 1: @@
-== Introduction ==
+==Introduction==
 This LinkSprint extension plate is a standard accessory for LinkSprite Arduino/pcDuino enclosure. By stacking multiple extension plate, the LinkSprite clear enclosure can allow multiple shield be to stack altogether.
@@ Line 12: / Line 12: @@
 [[File:enclosure5.jpg | 400px]]
-== Usage ==
+==Usage==
 *1. Install the pcDuino/Arduino enclosure as the normal one ([http://linksprite.com/wiki/index.php5?title=LinkSprite_Clear_Enclosure_for_Arduino#Usage step 1 to step 3]).
 *2. Fit the extension plate into the groove on the bottom panel.
@@ Line 26: / Line 26: @@
 [[File:enclosure4.jpg | 400px]]

@@ Line 1: / Line 1: @@
 == Introduction ==
-This LinkSprint extension plate is a standard accessory for LinkSprite Arduino/pcDuino enclosure. It allows the enclosure to have more internal space, so that you add more shields or experiment boards to pcDuino/Arduino, and still fit into the enclosure.
+This LinkSprint extension plate is a standard accessory for LinkSprite Arduino/pcDuino enclosure. By stacking multiple extension plate, the LinkSprite clear enclosure can allow multiple shield be to stack altogether.
 [[File:enclosure5.jpg | 400px]]

@@ Line 1: / Line 1: @@
 == Introduction ==
-This LinkSprint extension plate is a standard accessory for LinkSprite Arduino enclosure to make the case has more internal space, so that we you can use overlying more shields or boards to fit your project.
+This LinkSprint extension plate is a standard accessory for LinkSprite Arduino/pcDuino enclosure. It allows the enclosure to have more internal space, so that you add more shields or experiment boards to pcDuino/Arduino, and still fit into the enclosure.
 [[File:enclosure5.jpg | 400px]]
 == Usage ==
-*1. Installing the Arduino enclosure as the normal one ([http://linksprite.com/wiki/index.php5?title=LinkSprite_Clear_Enclosure_for_Arduino#Usage step 1 to step 3]).
+*1. Install the pcDuino/Arduino enclosure as the normal one ([http://linksprite.com/wiki/index.php5?title=LinkSprite_Clear_Enclosure_for_Arduino#Usage step 1 to step 3]).
-*2. Nestle the extension plate into the groove on the bottom panel.
+*2. Fit the extension plate into the groove on the bottom panel.
 *3. Insert the copper cylinder, you can install more extension plates if you have more shields or you need more internal space.
@@ Line 15: / Line 16: @@
 *4. Connect your project.
-*5. Instal the end pieces and drill them as your requirements.
+*5. Instal the end pieces and drill them according to your requirement.
 *6. Cover with the lid and fasten by the screws at last.
 [[File:enclosure4.jpg | 400px]]

@@ Line 15: / Line 15: @@
 *4. Connect your project.
-*5. Instal the end piece and drill them as your requirements.
+*5. Instal the end pieces and drill them as your requirements.
 *6. Cover with the lid and fasten by the screws at last.
 [[File:enclosure4.jpg | 400px]]

@@ Line 1: / Line 1: @@
 == Introduction ==
-This LinkSprint extension plate is a standard accessiorise for LinkSprite Arduino enclosure to make the case has more internal space, so that we you can use overlying more shields or boards to fit your project.
+This LinkSprint extension plate is a standard accessory for LinkSprite Arduino enclosure to make the case has more internal space, so that we you can use overlying more shields or boards to fit your project.
 The extension plate is made of the same material ABS with the Arduino enclosure, make case like a whole one. You can overlying one or two or more ,just need to fasten by the copper cylinder in the package.

← Older revision		Revision as of 09:45, 10 January 2013
Line 6:		Line 6:

	== Usage ==		== Usage ==
		+	*1. Installing the Arduino enclosure as the normal one ([http://linksprite.com/wiki/index.php5?title=LinkSprite_Clear_Enclosure_for_Arduino#Usage step 1 to step 3])
		+	*2. Nestle the extension plate into the groove on the bottom panel.
		+	*3. Insert the copper cylinder, you can install more extension plate if you have more shield or you need more internal space.
		+
		+	[[File:cucylinder1.jpg]]
		+
		+	[[file:cucylinder2.jpg]]
		+
		+	*4. Instal the end piece and drill them as your requirements.
		+	*5. Cover with the lid and fasten by the screws at last
		+
	[[File:enclosure4.jpg \| 400px]]		[[File:enclosure4.jpg \| 400px]]