Linker Mezzanine card for 96board - Revision history

Alvin: /* Description */

2015-12-25T06:26:25Z

‎Description

Alvin: /* Description */

2015-12-25T06:24:54Z

‎Description

Alvin at 05:37, 25 December 2015

2015-12-25T05:37:31Z

Alvin at 02:29, 25 December 2015

2015-12-25T02:29:47Z

Alvin at 02:09, 25 December 2015

2015-12-25T02:09:01Z

Alvin: /* 96Boards CE Minimum Hardware Features */

2015-12-25T02:08:21Z

‎96Boards CE Minimum Hardware Features

Alvin at 02:04, 25 December 2015

2015-12-25T02:04:51Z

Alvin: Created page with "== Introduction == == Features == There are 8 4-pin 2.54mm spacing housing on the card and these connectors covering Analog, UART I2C, and GPIO can connect Linker kit modul..."

2015-12-24T02:54:19Z

Created page with "== Introduction == == Features == There are 8 4-pin 2.54mm spacing housing on the card and these connectors covering Analog, UART I2C, and GPIO can connect Linker kit modul..."

New page

== Introduction ==

== Features ==

There are 8 4-pin 2.54mm spacing housing on the card and these connectors covering Analog, UART I2C, and GPIO can connect Linker kit modules directly.

== Schematic ==

== Demo ==

← Older revision		Revision as of 06:26, 25 December 2015
Line 1:		Line 1:
	==Description ==		==Description ==

−	[[File:1-4.~~jpg~~]]	+	[[File:1-5.png]]

← Older revision		Revision as of 06:24, 25 December 2015
Line 1:		Line 1:
	==Description ==		==Description ==
		+
		+	[[File:1-4.jpg]]
		+

	Linker Mezzanine card is a shield breadout board designed for 96board. All the Linker kit modules can be plugged onto 96board through this card. There are bidirectional voltage-level translators which allows for low-voltage bidirectional translation between any of the 1.2-V,1.5-V, 1.8-V, 2.5-V, 3.3-V, and 5-V voltage nodes. So it compatibles with 3.3V or 5V module and make connecting peripheral more easily. You just plug a jumper onto JP9 to select which input voltage do you have. Moreover, this shield has an on-board ADC chip so that analog output modules can be used on 96board. The ADC chip used is MCP3004. It talks to 96board using SPI interface.		Linker Mezzanine card is a shield breadout board designed for 96board. All the Linker kit modules can be plugged onto 96board through this card. There are bidirectional voltage-level translators which allows for low-voltage bidirectional translation between any of the 1.2-V,1.5-V, 1.8-V, 2.5-V, 3.3-V, and 5-V voltage nodes. So it compatibles with 3.3V or 5V module and make connecting peripheral more easily. You just plug a jumper onto JP9 to select which input voltage do you have. Moreover, this shield has an on-board ADC chip so that analog output modules can be used on 96board. The ADC chip used is MCP3004. It talks to 96board using SPI interface.

@@ Line 1: / Line 1: @@
 ==Description ==
 Linker Mezzanine card is a shield breadout board designed for 96board. All the Linker kit modules can be plugged onto 96board through this card. There are bidirectional voltage-level translators which allows for low-voltage bidirectional translation between any of the 1.2-V,1.5-V, 1.8-V, 2.5-V, 3.3-V, and 5-V voltage nodes. So it compatibles with 3.3V or 5V module and make connecting peripheral more easily. You just plug a jumper onto JP9 to select which input voltage do you have. Moreover, this shield has an on-board ADC chip so that analog output modules can be used on 96board. The ADC chip used is MCP3004. It talks to 96board using SPI interface.
 == Features ==
-There are 8 4-pin 2.54mm spacing housing on the card and these connectors covering Analog, UART I2C, and GPIO can connect Linker kit modules directly.
+*8 connecctors covering Analog, UART, I2C and GPIO
 == Schematic diagram ==
 [[File:1-4.jpg]]

@@ Line 1: / Line 1: @@
-== Introduction ==
+==Description ==
-The 96Boards initiative is designed to offer a single software and hardware community across multiple vendor boards supporting a range of different features. A fixed set of minimum functions including USB, SD, HDMI and standardized low speed and high speed peripheral connectors are provided. Vendors may add customized hardware and feature sets provided the minimum functions are available.
 == Features ==
-There are currently two 96Boards specifications for low-cost ARMv7-A and ARMv8-A development boards:
+There are 8 4-pin 2.54mm spacing housing on the card and these connectors covering Analog, UART I2C, and GPIO can connect Linker kit modules directly.
-Boards EE Minimum Hardware Features
+== Schematic diagram ==
-More information
+[[File:1-4.jpg]]

← Older revision		Revision as of 02:09, 25 December 2015
Line 72:		Line 72:
	More information		More information
	[http://www.96boards.org/]		[http://www.96boards.org/]
−
−	~~== Demo ==~~

@@ Line 32: / Line 32: @@
 HiKey LeMaker
-[[File:1.png]]
+[[File:1-3.png]]
 The HiKey board was the first board to be certified 96Boards Consumer Edition compatible. Two versions of this board are available: the original from CircuitCo and a new version in 1GB and 2GB variants from LeMaker. The board is based around the HiSilicon Kirin 6220  eight-core ARM Cortex-A53 64-bit SoC running at 1.2GHz and delivering over 10,000 Dhrystone VAX MIPS total performance. The SoC also delivers high performance 3D graphics support with its ARM Mali 450-MP4 GPU.
@@ Line 72: / Line 72: @@
 More information
 [http://www.96boards.org/]
 == Demo ==