Alvin: /* Load Demo */

2016-07-19T05:36:48Z

‎Load Demo

Alvin: /* Part list: */

2016-07-19T05:27:31Z

‎Part list:

Alvin: Created page with "= Introduction = Linker VEML6075 uses Vishay’s UVA and UVB Light Sensor VEML6075. The VEML6075 senses UVA and UVB light and incorporates photodiode, amplifiers, and analog..."

2016-07-19T05:26:58Z

Created page with "= Introduction = Linker VEML6075 uses Vishay’s UVA and UVB Light Sensor VEML6075. The VEML6075 senses UVA and UVB light and incorporates photodiode, amplifiers, and analog..."

New page

= Introduction =

Linker VEML6075 uses Vishay’s UVA and UVB Light Sensor VEML6075. The VEML6075 senses UVA and UVB light and incorporates photodiode, amplifiers, and analog / digital circuits into a single chip using a CMOS process. When the UV sensor is applied, it is able to detect UVA and UVB intensity to provide a measure of the signal strength as well as allowing for UVI measurement.

[[File:Linker6075.jpg| 480px]]

[[File:Linker6075 A.jpg| 480px]]

= Features =

*Operating voltage range : 3V - 5.5V
*Logic voltage range : 3V - 5.5V
*Supply current (TYP.) : 485uA
*Output type : I2C bus
*Industrial Temperature Range : -40℃ to +85℃
*16-bit resolution per channel
*Excellent UVA and UVB sensitivity
*Dimension: 24*23.6*9.2mm

= Applications =

*Handheld device
*Notebook
*Consumer device
*Industrial and medical application

= How to use =

== Part list: ==

Arduino UNO x1
Linker Base Shield x1
Linker Cable (20cm) x1
Linker VEML6075 x1

== Wiring ==

'''Connecting the Linker VEML6075 to the I2C interface of linker Base shield with linker cable ：'''

[[File:Linker6075 B.jpg| 480px]]

== Install Library ==

'''Place the VEML6075_master library folder your ”arduinosketchfolder/libraries/ folder”.'''

[[File:Linker6075 C.jpg| 480px]]

== Load Demo ==

'''Open File->Examples->VEML6075_Master->auto_mode and upload to your Arduino uno wired up to the sensor.'''

[[File:Linker6075 D.jpg| 480px]]

'''Please select the correct type and port of the board ：'''

[[File:Linker6075 E.jpg| 480px]]

'''Upload to the Arduino and open the serial console at 9600 baud to see the UV data output.'''

[[File:Linker6075 F.jpg| 480px]]

← Older revision		Revision as of 05:36, 19 July 2016
Line 62:		Line 62:

	[[File:Linker6075 F.jpg\| 480px]]		[[File:Linker6075 F.jpg\| 480px]]
		+
		+	= Resources =
		+
		+	[https://s3.amazonaws.com/linksprite/LinkerKit/vishay+sensors/Datasheet.zip Datasheet.zip]
		+
		+	[https://s3.amazonaws.com/linksprite/LinkerKit/vishay+sensors/libraries.zip libraries.zip]

@@ Line 30: / Line 30: @@
 Arduino UNO        	x1
 Linker Base Shield    	x1
 Linker Cable (20cm)  	x1
 Linker VEML6075    	x1

Linker VEML6075 - Revision history

Alvin: /* Load Demo */

Alvin: /* Part list: */

Alvin: Created page with "= Introduction = Linker VEML6075 uses Vishay’s UVA and UVB Light Sensor VEML6075. The VEML6075 senses UVA and UVB light and incorporates photodiode, amplifiers, and analog..."