MQ2 Smoke Detector Shield for Arduino - Revision history

Alvin: /* Resources */

2016-07-03T04:36:00Z

‎Resources

2016-06-20T12:57:42Z

‎Introduction

2015-09-16T08:14:45Z

2015-09-07T02:16:45Z

‎Introduction

2015-09-07T02:16:08Z

‎Introduction

2014-02-18T08:09:32Z

‎How to buy

2013-02-21T01:48:00Z

‎Introduction

2013-02-21T01:47:12Z

‎Introduction

2012-12-27T10:19:29Z

‎How to buy

2012-12-27T10:18:25Z

‎Resources

← Older revision		Revision as of 04:36, 3 July 2016
Line 153:		Line 153:

	*[https://s3.amazonaws.com/linksprite/Shields/MQ2/MQ2.pdf MQ2 Datasheet]		*[https://s3.amazonaws.com/linksprite/Shields/MQ2/MQ2.pdf MQ2 Datasheet]
		+	*[https://s3.amazonaws.com/linksprite/MQ-2/TECHNICAL+DATA+MQ-2+GAS+SENSOR.pdf TECHNICAL DATA MQ-2 GAS SENSOR]

	== How to buy ==		== How to buy ==

← Older revision		Revision as of 12:57, 20 June 2016
Line 12:		Line 12:
	[[File:N98DG WITHOUT PACKAGED BACK.jpg\|640px]]		[[File:N98DG WITHOUT PACKAGED BACK.jpg\|640px]]

		+	Below photos are for shields without headers:
		+
		+	[[File:MQ2 Smoke Detector Shield for Arduino 001.jpg\|640px]]
		+
		+	[[File:MQ2 Smoke Detector Shield for Arduino 002.jpg\|640px]]
		+
		+	[[File:MQ2 Smoke Detector Shield for Arduino 003.jpg\|640px]]

	== Features ==		== Features ==

← Older revision		Revision as of 08:14, 16 September 2015
Line 12:		Line 12:
	[[File:N98DG WITHOUT PACKAGED BACK.jpg\|640px]]		[[File:N98DG WITHOUT PACKAGED BACK.jpg\|640px]]

−	~~[[File:N98DG PACKAGED FRONT.jpg\|640px]]~~
−
−	~~[[File:N98DG PACKAGED BACK.jpg\|640px]]~~

	== Features ==		== Features ==

@@ Line 8: / Line 8: @@
 Connecting five volts across the heating (H) pins keeps the sensor hot enough to function correctly. Connecting five volts at either the A or B pins causes the sensor to emit an analog voltage on the other pins. A resistive load between the output pins and ground sets the sensitivity of the detector. Please note that the picture in the datasheet for the top configuration is wrong. Both configurations have the same pinout consistent with the bottom configuration.The resistive load should be calibrated for your particular application using the equations in the datasheet, but a good starting value for the resistor is 20 kΩ.
-[[File:N98DG WITHOUT PACKAGED FRONT.jpg | 640PX]]
+[[File:N98DG WITHOUT PACKAGED FRONT.jpg | 640px]]
 [[File:N98DG WITHOUT PACKAGED BACK.jpg|640px]]

@@ Line 8: / Line 8: @@
 Connecting five volts across the heating (H) pins keeps the sensor hot enough to function correctly. Connecting five volts at either the A or B pins causes the sensor to emit an analog voltage on the other pins. A resistive load between the output pins and ground sets the sensitivity of the detector. Please note that the picture in the datasheet for the top configuration is wrong. Both configurations have the same pinout consistent with the bottom configuration.The resistive load should be calibrated for your particular application using the equations in the datasheet, but a good starting value for the resistor is 20 kΩ.
-[[File:MQ2_SHIELD_1.jpg | 400PX]]
+[[File:N98DG WITHOUT PACKAGED FRONT.jpg | 640PX]]
 == Features  ==

@@ Line 146: / Line 146: @@
 == How to buy  ==
-You can order from [http://www.linkspritedirect.com/product_info.php?products_id=151 LinkSpriteDirect] or [http://www.cutedigi.com/arduino-shields/mq2-smoke-detector-shield-for-arduino.html  CuteDigi].
+You can order from [http://store.linksprite.com/mq2-smoke-detector-shield-for-arduino-pcduino/ LinkSprite Store] or [http://www.cutedigi.com/arduino-shields/mq2-smoke-detector-shield-for-arduino.html  CuteDigi].
 == See Also  ==

← Older revision		Revision as of 01:47, 21 February 2013
Line 7:		Line 7:

	Connecting five volts across the heating (H) pins keeps the sensor hot enough to function correctly. Connecting five volts at either the A or B pins causes the sensor to emit an analog voltage on the other pins. A resistive load between the output pins and ground sets the sensitivity of the detector. Please note that the picture in the datasheet for the top configuration is wrong. Both configurations have the same pinout consistent with the bottom configuration.The resistive load should be calibrated for your particular application using the equations in the datasheet, but a good starting value for the resistor is 20 kΩ.		Connecting five volts across the heating (H) pins keeps the sensor hot enough to function correctly. Connecting five volts at either the A or B pins causes the sensor to emit an analog voltage on the other pins. A resistive load between the output pins and ground sets the sensitivity of the detector. Please note that the picture in the datasheet for the top configuration is wrong. Both configurations have the same pinout consistent with the bottom configuration.The resistive load should be calibrated for your particular application using the equations in the datasheet, but a good starting value for the resistor is 20 kΩ.
		+
		+	[[File:MQ2_SHIELD_1.jpg]]

	== Features ==		== Features ==

← Older revision		Revision as of 10:18, 27 December 2012
Line 140:		Line 140:


−	*[https://s3.amazonaws.com/linksprite/Shields/MQ2/MQ2.pdf Datasheet]	+	*[https://s3.amazonaws.com/linksprite/Shields/MQ2/MQ2.pdf MQ2 Datasheet]

	== How to buy ==		== How to buy ==