Oxygen Sensor - Revision history

Alvin: /* Recources */

2017-06-15T07:21:33Z

‎Recources

2014-12-16T03:12:19Z

‎Schematic

2014-10-31T01:45:45Z

‎Recources

2014-10-31T01:37:54Z

‎Usage

2014-10-31T01:25:28Z

2014-10-18T05:01:34Z

2014-10-18T05:01:03Z

Created page with " 400px"

New page

[[File:Linker O2 1.jpg| 400px]]

@@ Line 57: / Line 57: @@
 == Recources ==
-*[https://s3.amazonaws.com/linksprite/LinkerKit/K1059654193.pdf Datasheet of ME-O3 sensor]
+*[https://s3.amazonaws.com/linksprite/LinkerKit/ME2-O2-D20+0-25%25+Manual+(ver1.2).pdf Datasheet of ME2-O2 sensor]
 *[https://s3.amazonaws.com/linksprite/LinkerKit/LINKER_O2.ino Linker O2 Example Code]

@@ Line 6: / Line 6: @@
 [[File:Linker O2 1.jpg| 400px]]
 [[File:Linker O2 2.jpg | 400px]]
 == Schematic ==

← Older revision		Revision as of 01:45, 31 October 2014
Line 54:		Line 54:
	*[https://s3.amazonaws.com/linksprite/LinkerKit/K1059654193.pdf Datasheet of ME-O3 sensor]		*[https://s3.amazonaws.com/linksprite/LinkerKit/K1059654193.pdf Datasheet of ME-O3 sensor]
	*[https://s3.amazonaws.com/linksprite/LinkerKit/LINKER_O2.ino Linker O2 Example Code]		*[https://s3.amazonaws.com/linksprite/LinkerKit/LINKER_O2.ino Linker O2 Example Code]
		+
		+	== How to buy ==
		+
		+	Here to buy Oxygen (O2) Sensor Module of Linker Kit for pcDuino/Arduino on [http://store.linksprite.com/oxygen-o2-sensor-module-of-linker-kit-for-pcduino-arduino/ store]

← Older revision		Revision as of 01:37, 31 October 2014
Line 13:		Line 13:
	== Usage ==		== Usage ==

		+	<syntaxhighlight lang="c">
		+
		+	#include <math.h>
		+	const int buzzerPin=3; //Connect the Buzzer module to Pin3, Digital 3
		+	float thresholdVoltage= 1.84; //The treshold for which the Buzzer should sound.
		+	void setup()
		+	{
		+	Serial.begin(9600); //Start the Serial connection
		+	pinMode(buzzerPin,OUTPUT); //Set the LED on Digital 12 as an OUTPUT
		+
		+	}
		+	void loop()
		+	{
		+
		+	float sensorValue;
		+	float sensorVoltage;
		+	sensorValue = analogRead(A2);
		+	sensorVoltage =(sensorValue/1024)*5.0;
		+
		+	if(sensorVoltage<thresholdVoltage)
		+	{
		+	digitalWrite(buzzerPin,HIGH);
		+	}
		+	else
		+	{
		+	digitalWrite(buzzerPin,LOW);
		+	}
		+	sensorVoltage = sensorVoltage/101*1000;
		+	Serial.println("the output voltage is:");
		+
		+	Serial.print(sensorVoltage);
		+	Serial.println("mV");
		+	delay(1000);
		+	}
		+
		+	</syntaxhighlight>

	== Recources ==		== Recources ==

← Older revision		Revision as of 01:25, 31 October 2014
Line 1:		Line 1:
		+	== Introduction ==

		+	Linker Oxygen sensor module uses ME series O2 sensor, and have low consumption , small size, high sensitivity , wide range of linearity , and better anti-jamming capacity, good reproducibility, stability and reliability ect advantage . It is electrochemical sensor widely suits for mine, industry and environmental protection field
		+	ect.

	[[File:Linker O2 1.jpg\| 400px]]		[[File:Linker O2 1.jpg\| 400px]]
	[[File:Linker O2 2.jpg \| 400px]]		[[File:Linker O2 2.jpg \| 400px]]
		+
		+	== Schematic ==
		+
		+	*[https://s3.amazonaws.com/linksprite/LinkerKit/Linker_O2_Schematic.pdf Linker O2 Schematic]
		+
		+	== Usage ==
		+
		+
		+	== Recources ==
		+
		+	*[https://s3.amazonaws.com/linksprite/LinkerKit/K1059654193.pdf Datasheet of ME-O3 sensor]
		+	*[https://s3.amazonaws.com/linksprite/LinkerKit/LINKER_O2.ino Linker O2 Example Code]