RS485/GPIO Shield for Raspberry Pi V3.0 - Revision history

Alvin: /* Introduction */

2016-10-11T02:37:33Z

‎Introduction

Alvin: /* Introduction */

2016-10-11T02:34:09Z

‎Introduction

Alvin at 02:13, 11 May 2016

2016-05-11T02:13:47Z

Youkee at 01:56, 24 November 2015

2015-11-24T01:56:07Z

Qian.zhang: Created page with "== Introduction == This is a shield to add a RS485 level shift to the UART of Raspberry Pi. Moreover, it also breakout the rest headers for easy access. It's a new version w..."

2015-01-06T01:00:30Z

Created page with "== Introduction == This is a shield to add a RS485 level shift to the UART of Raspberry Pi. Moreover, it also breakout the rest headers for easy access. It's a new version w..."

New page

== Introduction ==

This is a shield to add a RS485 level shift to the UART of Raspberry Pi. Moreover, it also breakout the rest headers for easy access.

It's a new version which compatible with Raspberry Pi B+ .

[[File:RS485 V3 for RPi_1.jpg]]

[[File:RS485 V3 for RPi_2.jpg]]

[[File:RS485 V3 for RPi_3.jpg]]

== Schematics ==

*[https://s3.amazonaws.com/linksprite/Shields/RS485_RPI/(NEW)RS485+shield+for+RPi.pdf schematics]

== Usage ==

The UART on Raspberry Pi is on P1 and shown below:

[[File:RPI UART.png]]

The UART is /dev/ttyAMAO, it defaults to output system log. But if user wants to use this UART to connect to other modules through UART, for example, GPS module, we need to change the configuration.

The detailed steps are as following:

We need to modify two files: /boot/cmdline.txt and /etc/inittab.

Modify /boot/cmdline.txt:

Replace the original content:

dwc_otg.lpm_enable=0 console=ttyAMA0,115200 kgdboc=ttyAMA0,115200 console=tty1 root=/dev/mmcblk0p2 rootfstype=ext4 elevator=deadline rootwait

With:

dwc_otg.lpm_enable=0 console=tty1 root=/dev/mmcblk0p2 rootfstype=ext4 elevator=deadline rootwait

Modify /etc/inittab:

Comment out the last line of /etc/inittab. To comment out, it simply addess a '#'.

$ sudo vi /etc/inittab
#T0:23:respawn:/sbin/getty -L ttyAMA0 115200 vt100

Save the changes, and reboot. We will get an UART with baud rate of 115200.

== Resources ==

*[http://learn.linksprite.com/raspberry-pi/shield/user-tips-of-rs485-shield-for-rpi/ User Guide of RS485 Shield for Raspberry Pi]

@@ Line 6: / Line 6: @@
-[[File:RS485 GPIO 101203002-001.jpg]]
+[[File:RS485 GPIO 101203002-001.jpg| 640px]]
-[[File:RS485 GPIO 101203002-002.jpg]]
+[[File:RS485 GPIO 101203002-002.jpg| 640px]]
-[[File:RS485 GPIO 101203002-003.jpg]]
+[[File:RS485 GPIO 101203002-003.jpg| 640px]]
 == Schematics ==

@@ Line 5: / Line 5: @@
 It's a new version which compatible with Raspberry Pi B+/Raspberry Pi 3 Model B/Raspberry Pi 2 Model B.
-[[File:RS485 V3 for RPi_2.jpg]]
+[[File:RS485 GPIO 101203002-001.jpg]]
-[[File:RS485 V3 for RPi_3.jpg]]
+[[File:RS485 GPIO 101203002-002.jpg]]
 == Schematics ==

@@ Line 3: / Line 3: @@
 This is a shield to add a RS485 level shift to the UART of Raspberry Pi. Moreover, it also breakout the rest headers for easy access.
-It's a new version which compatible with Raspberry Pi B+ .
+It's a new version which compatible with Raspberry Pi B+/Raspberry Pi 3 Model B/Raspberry Pi 2 Model B.
 [[File:RS485 V3 for RPi_1.jpg]]

@@ Line 13: / Line 13: @@
 == Schematics ==
-*[https://s3.amazonaws.com/linksprite/Shields/RS485_RPI/(NEW)RS485+shield+for+RPi.pdf schematics]
+*[https://s3.amazonaws.com/linksprite/Shields/RS485_RPI/RS485+Shield+for+RPi+B%2B.PDF schematics]
 == Usage ==