Serial port bluetooth module (Master/Slave) - Revision history

Katherine.d: /* Cautions */

2012-12-12T09:50:54Z

‎Cautions

Katherine.d: /* How to set up connections between two BluetoothBee step by step */

2012-12-12T09:36:13Z

‎How to set up connections between two BluetoothBee step by step

Katherine.d: /* How to set up connections between two BluetoothBee step by step */

2012-12-12T09:33:51Z

‎How to set up connections between two BluetoothBee step by step

Katherine.d: /* How to set up connections between two BluetoothBee step by step */

2012-12-12T09:19:21Z

‎How to set up connections between two BluetoothBee step by step

Katherine.d: /* Additional Idea */

2012-12-12T09:15:39Z

‎Additional Idea

Katherine.d: /* Support */

2012-12-12T09:04:00Z

‎Support

Katherine.d: /* See Also */

2012-12-12T09:02:25Z

‎See Also

Katherine.d: /* How to buy */

2012-12-12T09:01:37Z

‎How to buy

Katherine.d: /* Additional Idea */

2012-12-12T08:27:44Z

‎Additional Idea

Katherine.d: /* Resources */

2012-12-12T08:27:16Z

‎Resources

@@ Line 42: / Line 42: @@
 == Cautions  ==
 *While using with Arduino, set the operation voltage to 5V. Else use a proper logic level converter.
 *While using with UartSBee, set the operation voltage to 5V.
 *Command to change baud rate is persistent even after reset. Hence remember the baud rate for next use.
 == Specification  ==

@@ Line 390: / Line 390: @@
 Terminal tool run on PC: '''sscom32E.exe'''[https://s3.amazonaws.com/linksprite/components_breakout/Serial_port_bluetooth_module+/sscom32E.zip Download]
-*1.  Connect two BluetoothBee to PC through UartSB.(Green led blinks 2times/1s)
+*'''1. Connect two BluetoothBee to PC through UartSB.'''(Green led blinks 2times/1s)
 [[File:BMsetup01.jpg | 400px]]
-*2.  Open two sscom32E terminals and set the configuration as following.
+*'''2. Open two sscom32E terminals and set the configuration as following.'''
 [[File:BMsetup02.jpg | 400px]]
-* Set one Bluetooth as master and start inquiring
+*'''3. Set one Bluetooth as master and start inquiring.'''
 :(1) Choose '''SendNew''' and click '''SEND''' with empty data. (This actually is to send “\r\n”)
@@ Line 413: / Line 413: @@
 [[File:BMsetup05.jpg | 400px]]
-*4.  Set the other Bluetooth as slave and enable been inquired.
+*'''4. Set the other Bluetooth as slave and enable been inquired.'''
 :(1) Send “\r\n”
@@ Line 425: / Line 425: @@
 [[File:BMsetup07.jpg | 400px]]
-*5.  At this point, you will find in the master terminal will display info like following:
+*'''5. At this point, you will find in the master terminal will display info like following:'''
 [[File:BMsetup08.jpg | 400px]]
@@ Line 433: / Line 433: @@
 The info '''+RTINQ=0,18,E4,24,90,4;SK00MSE''' means the master has searched a Bluetooth device (slave) with the address “0,18,E4,24,90,4” and the name “SK00MSE”.
-*6.  Connect to the slave. (In master terminal)
+*'''6. Connect to the slave. '''(In master terminal)
 :(1) Send “\r\n”
@@ Line 446: / Line 446: @@
 [[File:BMsetup11.jpg | 400px]]
-*7.  How to disconnect two devices.
+*'''7. How to disconnect two devices.'''
 The default configuration will make two paired Bluetooth auto connect when powered. If you want to disconnect them, you may need to pull PIO0 high.

@@ Line 392: / Line 392: @@
 *1.  Connect two BluetoothBee to PC through UartSB.(Green led blinks 2times/1s)
-[[File:BMsetup01.jpg]]
+[[File:BMsetup01.jpg | 400px]]
 *2.  Open two sscom32E terminals and set the configuration as following.
-[[File:BMsetup02.jpg]]
+[[File:BMsetup02.jpg | 400px]]
 * Set one Bluetooth as master and start inquiring
@@ Line 402: / Line 402: @@
 :(1) Choose '''SendNew''' and click '''SEND''' with empty data. (This actually is to send “\r\n”)
-[[File:BMsetup03.jpg]]
+[[File:BMsetup03.jpg | 400px]]
 :(2) Set Bluetooth as master
-[[File:BMsetup04.jpg]]
+[[File:BMsetup04.jpg | 400px]]
 :(3) Send “\r\n” as (1)
 :(4) Make master start inquiring. (Green and Red Led blink 2times/1s in interval)
-[[File:BMsetup05.jpg]]
+[[File:BMsetup05.jpg | 400px]]
 *4.  Set the other Bluetooth as slave and enable been inquired.
@@ Line 418: / Line 418: @@
 :(2) Set Bluetooth as slave
-[[File:BMsetup06.jpg]]
+[[File:BMsetup06.jpg | 400px]]
 :(3) Send “\r\n”
 :(4) Enable slave been inquired. (Green and Red Led blink 2times/1s in interval)
-[[File:BMsetup07.jpg]]
+[[File:BMsetup07.jpg | 400px]]
 *5.  At this point, you will find in the master terminal will display info like following:
-[[File:BMsetup08.jpg]]
+[[File:BMsetup08.jpg | 400px]]
 The info '''+WENDY''' may be the Bluetooth of somebody’s cellphone.
@@ Line 438: / Line 438: @@
 :(2) Connect to the slave as following
-[[File:BMsetup09.jpg]]
+[[File:BMsetup09.jpg | 400px]]
 If the green led on master and slave is blinking 1time/2s, congratulations, you have established the connection between Bluetooth. And now you can send any info to each other.
-[[File:BMsetup10.jpg]]
+[[File:BMsetup10.jpg | 400px]]
-[[File:BMsetup11.jpg]]
+[[File:BMsetup11.jpg | 400px]]
 *7.  How to disconnect two devices.
@@ Line 454: / Line 454: @@
 One another way to send the command is all in hex mode like following:
-[[File:BMsetup12.jpg]]
+[[File:BMsetup12.jpg | 400px]]
 == Resources  ==

@@ Line 392: / Line 392: @@
 *1.  Connect two BluetoothBee to PC through UartSB.(Green led blinks 2times/1s)
-[[File:setup01.jpg]]
+[[File:BMsetup01.jpg]]
 *2.  Open two sscom32E terminals and set the configuration as following.
-[[File:setup02.jpg]]
+[[File:BMsetup02.jpg]]
 * Set one Bluetooth as master and start inquiring
@@ Line 402: / Line 402: @@
 :(1) Choose '''SendNew''' and click '''SEND''' with empty data. (This actually is to send “\r\n”)
-[[File:setup03.jpg]]
+[[File:BMsetup03.jpg]]
 :(2) Set Bluetooth as master
-[[File:setup04.jpg]]
+[[File:BMsetup04.jpg]]
 :(3) Send “\r\n” as (1)
 :(4) Make master start inquiring. (Green and Red Led blink 2times/1s in interval)
-[[File:setup05.jpg]]
+[[File:BMsetup05.jpg]]
 *4.  Set the other Bluetooth as slave and enable been inquired.
@@ Line 418: / Line 418: @@
 :(2) Set Bluetooth as slave
-[[File:setup06.jpg]]
+[[File:BMsetup06.jpg]]
 :(3) Send “\r\n”
 :(4) Enable slave been inquired. (Green and Red Led blink 2times/1s in interval)
-[[File:setup07.jpg]]
+[[File:BMsetup07.jpg]]
 *5.  At this point, you will find in the master terminal will display info like following:
-[[File:setup08.jpg]]
+[[File:BMsetup08.jpg]]
 The info '''+WENDY''' may be the Bluetooth of somebody’s cellphone.
@@ Line 438: / Line 438: @@
 :(2) Connect to the slave as following
-[[File:setup09.jpg]]
+[[File:BMsetup09.jpg]]
 == Resources  ==

← Older revision		Revision as of 09:15, 12 December 2012
Line 385:		Line 385:

	== Additional Idea ==		== Additional Idea ==
		+
		+	=== How to set up connections between two BluetoothBee step by step ===
		+
		+	Terminal tool run on PC: '''sscom32E.exe'''[https://s3.amazonaws.com/linksprite/components_breakout/Serial_port_bluetooth_module+/sscom32E.zip Download]
		+
		+	*1. Connect two BluetoothBee to PC through UartSB.(Green led blinks 2times/1s)
		+
		+	[[File:setup01.jpg]]
		+
		+	*2. Open two sscom32E terminals and set the configuration as following.
		+
		+	[[File:setup02.jpg]]
		+
		+	* Set one Bluetooth as master and start inquiring
		+
		+	:(1) Choose '''SendNew''' and click '''SEND''' with empty data. (This actually is to send “\r\n”)
		+
		+	[[File:setup03.jpg]]
		+
		+	:(2) Set Bluetooth as master
		+
		+	[[File:setup04.jpg]]
		+
		+	:(3) Send “\r\n” as (1)
		+	:(4) Make master start inquiring. (Green and Red Led blink 2times/1s in interval)
		+
		+	[[File:setup05.jpg]]
		+
		+	*4. Set the other Bluetooth as slave and enable been inquired.
		+
		+	:(1) Send “\r\n”
		+	:(2) Set Bluetooth as slave
		+
		+	[[File:setup06.jpg]]
		+
		+	:(3) Send “\r\n”
		+	:(4) Enable slave been inquired. (Green and Red Led blink 2times/1s in interval)
		+
		+	[[File:setup07.jpg]]
		+
		+	*5. At this point, you will find in the master terminal will display info like following:
		+
		+	[[File:setup08.jpg]]
		+
		+	The info '''+WENDY''' may be the Bluetooth of somebody’s cellphone.
		+
		+	The info '''+RTINQ=0,18,E4,24,90,4;SK00MSE''' means the master has searched a Bluetooth device (slave) with the address “0,18,E4,24,90,4” and the name “SK00MSE”.
		+
		+	*6. Connect to the slave. (In master terminal)
		+
		+	:(1) Send “\r\n”
		+	:(2) Connect to the slave as following
		+
		+	[[File:setup09.jpg]]

	== Resources ==		== Resources ==

@@ Line 397: / Line 397: @@
 == Support  ==
-If you have questions or other better design ideas, you can go to our [http://www.seeedstudio.com/forum forum] or [http://wish.seeedstudio.com wish] to discuss.<br>
+If you have questions or other better design ideas, you can go to our [http://www.linksprite.com/forum/index.php forum] to discuss.<br>
 == How to buy  ==

← Older revision		Revision as of 09:02, 12 December 2012
Line 402:		Line 402:

	== See Also ==		== See Also ==
−
−	*[http://www.seeedstudio.com/depot/grove-serial-bluetooth-p-795.html?cPath=139_142 Grove - Serial Bluetooth]<br>
−	*[http://www.seeedstudio.com/depot/bluetooth-bee-standalone-p-1157.html?cPath=139_142 Bluetooth Bee - Standalone]
−	*[http://www.seeedstudio.com/depot/bluetooth-shield-p-866.html?cPath=132_134 Bluetooth Shield]
−	*[http://www.seeedstudio.com/depot/bluetooth-bee-p-598.html?cPath=139_142 Bluetooth Bee]

	== Licensing ==		== Licensing ==

← Older revision		Revision as of 09:01, 12 December 2012
Line 400:		Line 400:

	== How to buy ==		== How to buy ==
−
−	~~Click here to buy: [http://www.seeedstudio.com/depot/serial-port-bluetooth-module-masterslave-p-572.html?cPath=139_142 Serial port bluetooth module (Master/Slave)]~~

	== See Also ==		== See Also ==

← Older revision		Revision as of 08:27, 12 December 2012
Line 385:		Line 385:

	== Additional Idea ==		== Additional Idea ==
−
−	*[http://www.seeedstudio.com/forum/viewtopic.php?f=18&t=1436&p=5637#p5637 How to set PC connect with Serial Bluetooth Grove]
−	*[http://www.seeedstudio.com/forum/viewtopic.php?f=4&t=687 Set up connections between two Bluetooth modules step by step]

	== Resources ==		== Resources ==

@@ Line 391: / Line 391: @@
 == Resources  ==
-*[http://www.seeedstudio.com/wiki/File:Bluetooth_Software_Instruction.pdf Software instruction]
+*[https://s3.amazonaws.com/linksprite/components_breakout/Serial_port_bluetooth_module+/Bluetooth_Software_Instruction.pdf Software instruction]
-*[http://www.seeedstudio.com/wiki/File:Bluetooth_module.pdf Bluetooth module Datasheet]
+*[https://s3.amazonaws.com/linksprite/components_breakout/Serial_port_bluetooth_module+/Bluetooth_module.pdf Bluetooth module Datasheet]
 == FAQ  ==