Solar Charger - Revision history

Alvin: /* Feature */

2016-06-03T06:52:12Z

‎Feature

Alvin: /* Introduction */

2016-06-03T06:47:30Z

‎Introduction

Alvin at 06:32, 3 June 2016

2016-06-03T06:32:45Z

Alvin at 06:29, 3 June 2016

2016-06-03T06:29:09Z

Alvin at 06:26, 3 June 2016

2016-06-03T06:26:04Z

Alvin: Created page with "== Introduction == Solar Charger is single lithium battery charging management module which can be powered by solar panels, as the main components of the module is CN3083..."

2016-06-03T06:23:50Z

Created page with "== Introduction == Solar Charger is single lithium battery charging management module which can be powered by solar panels, as the main components of the module is CN3083..."

New page

== Introduction ==

Solar Charger is single lithium battery charging management module which can be powered by solar panels, as the main components of the module is CN3083. The device includes an internal power transistor, and the application does not require an external current sense resistor and blocking diode.The internal 8-bit analog - digital conversion circuit could automatically adjusts the charging current according to current output capacity of input voltage source, the user does not need to consider the worst case, and it can maximally use current output capacity of the input voltage source, very suitable for the application of lithium battery charging powered by voltage source with limited current output capacity such as solar panel.CN3083 requires minimal external components, and complies with the USB bus specification, ideally suited for portable application fields. Thermal modulation circuit could control the chip temperature in safe range when the components power consumption or ambient temperature is relatively high. Internally fixed constant voltage charging voltage is 4.2V, can also be adjusted by an external resistor. Charging current could be set by an external resistor. When the input voltage power down, CN3083 automatically enters a low power consumption sleep mode, dropping the battery current consumption is less than 3 microamps. Other functions include input voltage too low latch,, automatic recharge, battery temperature monitor and charging status /charging completion indication etc.

== Feature ==

1. Using advanced degree CN3083 chip
2. Dual input and output compatible with universal wiring
3. Charging status pin lead out, facilitate the secondary development
4. Charging status indicated by LED

== Schematic Diagram ==

== Use ==

Solar Charger input voltage is 4.6-6.0V, output 4.2V, there are status indicators, bright red status light when charging, bright green status lights when charging is completed.
Charging current is generally about 500mA, which will change as the battery electric quantity changes.
Input and output are respectively provided two interfaces, VIN1, VIN2, VOUT1, VOUT2. With "+", "-" sign as a power source positive and negative.

[[File:solar charger 5.png]]

← Older revision		Revision as of 06:47, 3 June 2016
Line 12:		Line 12:


−	Solar Charger is single lithium battery charging management module which can be powered by solar panels, as the main components of the module is CN3083. The device includes an internal power transistor, and the application does not require an external current sense resistor and blocking diode.The internal 8-bit analog - digital conversion circuit could automatically adjusts the charging current according to current output capacity of input voltage source, the user does not need to consider the worst case, and it can maximally use current output capacity of the input voltage source, very suitable for the application of lithium battery charging powered by voltage source with limited current output capacity such as solar panel.CN3083 requires minimal ~~external~~ components, and complies with the USB bus specification, ideally suited for portable application fields. Thermal modulation circuit could control the chip temperature in safe range when the components power consumption or ambient temperature is relatively high. Internally fixed constant voltage charging voltage is 4.2V, can also be adjusted by an external resistor. Charging current could be set by an external resistor. When the input voltage power down, CN3083 automatically enters a low power consumption sleep mode, dropping the battery current consumption is less than 3 microamps. Other functions include input voltage too low latch,, automatic recharge, battery temperature monitor and charging status /charging completion indication etc.	+	Solar Charger is single lithium battery charging management module which can be powered by solar panels, as the main components of the module is CN3083. The device includes an internal power transistor, and the application does not require an external current sense resistor and blocking diode.The internal 8-bit analog - digital conversion circuit could automatically adjusts the charging current according to current output capacity of input voltage source, the user does not need to consider the worst case, and it can maximally use current output capacity of the input voltage source, very suitable for the application of lithium battery charging powered by voltage source with limited current output capacity such as solar panel.CN3083 requires minimal peripheral components, and complies with the USB bus specification, ideally suited for portable application fields. Thermal modulation circuit could control the chip temperature in safe range when the components power consumption or ambient temperature is relatively high. Internally fixed constant voltage charging voltage is 4.2V, can also be adjusted by an external resistor. Charging current could be set by an external resistor. When the input voltage power down, CN3083 automatically enters a low power consumption sleep mode, dropping the battery current consumption is less than 3 microamps. Other functions include input voltage too low latch,, automatic recharge, battery temperature monitor and charging status /charging completion indication etc.

	== Feature ==		== Feature ==

← Older revision	Revision as of 06:32, 3 June 2016
Line 2:	Line 2:


	+	[[File:solar charger 1.jpg\| 640px]]

	+	[[File:solar charger 2.jpg\| 640px]]
	+
	+	[[File:solar charger 3.jpg\| 640px]]
	+
	+	[[File:solar charger 4.jpg\| 640px]]

@@ Line 1: / Line 1: @@
 == Introduction  ==
@@ Line 16: / Line 18: @@
 == Schematic Diagram ==
+[https://s3.amazonaws.com/linksprite/robot/Solar+Charger+Board+V1.0.pdf]
 == Use ==
@@ Line 26: / Line 28: @@
 [[File:solar charger 5.png| 640px]]

← Older revision		Revision as of 06:26, 3 June 2016
Line 25:		Line 25:


−	[[File:solar charger 5.png]]	+	[[File:solar charger 5.png\| 640px]]

@@ Line 16: / Line 16: @@
 == Feature ==
-. Using advanced degree CN3083 chip
+*1. Using advanced degree CN3083 chip
-. Dual input and output compatible with universal wiring
+*2. Dual input and output compatible with universal wiring
-. Charging status pin lead out, facilitate the secondary development
+*3. Charging status pin lead out, facilitate the secondary development
-. Charging status indicated by LED
+*4. Charging status indicated by LED
 == Schematic Diagram ==