Stepper Motor with Cable - Revision history

Jingfeng at 12:28, 24 September 2013

2013-09-24T12:28:26Z

2013-09-24T12:25:57Z

2013-09-24T12:17:45Z

‎Wiring Example

2013-09-24T12:17:31Z

‎Wiring Example

2013-09-24T12:17:01Z

‎Wiring Example

2013-09-24T12:16:01Z

‎Wiring Example

2013-09-24T12:14:38Z

‎Wiring Example

2013-09-24T12:13:13Z

2013-09-24T12:03:36Z

‎Specification

2013-09-24T12:03:26Z

‎Specification

← Older revision		Revision as of 12:28, 24 September 2013
Line 1:		Line 1:
		+	This is a stepper motor with 6-wire and 2-phase.

	[[File:Stepper motor 1.jpg \| 450px]]		[[File:Stepper motor 1.jpg \| 450px]]

← Older revision		Revision as of 12:25, 24 September 2013
Line 108:		Line 108:

	</syntaxhighlight>		</syntaxhighlight>
		+
		+	== Tips==
		+	6-wire 2-phase stepper motor has 2 coils. The following is going to explain how to find out the common wire and how the group is divided.
		+
		+	*Use 200ohm of the multimeter.
		+	*Fix one probe of multimeter to one wire, and scan the other probe to other wires, mark the wire showing resistance value (10ohm or 20 ohm). These three wires belong to one group, and noted as R1 and R1.
		+	* If R1=R2, the wire attached to fixed probe is COM.
		+	* If R1=2*R2, the wire that shows resister value for the first time is the COM.
		+	if R1= 1/2 R2, the wire that shows resister value for the second time is the COM.
		+
		+	We can use the above method to find out the other coil.

← Older revision		Revision as of 12:17, 24 September 2013
Line 38:		Line 38:
	[[File:Stepper motor wire.JPG]]		[[File:Stepper motor wire.JPG]]

		+	The Arduino sample code is attached.

	<syntaxhighlight lang="c">		<syntaxhighlight lang="c">

← Older revision		Revision as of 12:17, 24 September 2013
Line 37:		Line 37:

	[[File:Stepper motor wire.JPG]]		[[File:Stepper motor wire.JPG]]
		+
		+
		+	<syntaxhighlight lang="c">
		+	int pinI1=8;//define I1 interface
		+	int pinI2=11;//define I2 interface
		+	int speedpinA=9;//enable motor A
		+	int pinI3=12;//define I3 interface
		+	int pinI4=13;//define I4 interface
		+	int speedpinB=10;//enable motor B
		+	#define spead 20 //set stepper motor spead,
		+	#define Beats 4 //select 8 beats or 4 beats
		+	char table[Beats];
		+	void set_beats_number()
		+	{
		+	if(Beats==4)
		+	{
		+	table[0] = 0x05;
		+	table[1] =0x09;
		+	table[2] =0x0A;
		+	table[3] =0x06;
		+	}
		+	else
		+	{
		+	table[0] = 0x01;
		+	table[1] = 0x05;
		+	table[2] = 0x04;
		+	table[3] = 0x06;
		+	table[4] = 0x02;
		+	table[5] = 0x0A;
		+	table[6] = 0x08;
		+	table[7] = 0x09;
		+	}
		+	}
		+
		+	void setup()
		+	{
		+	set_beats_number();
		+	pinMode(pinI1,OUTPUT);
		+	pinMode(pinI2,OUTPUT);
		+	pinMode(speedpinA,OUTPUT);
		+	pinMode(pinI3,OUTPUT);
		+	pinMode(pinI4,OUTPUT);
		+	pinMode(speedpinB,OUTPUT);
		+	digitalWrite(speedpinA,HIGH);
		+	digitalWrite(speedpinB,HIGH);
		+	}
		+
		+	void beat_control(char beat)
		+	{
		+	digitalWrite(pinI1,beat&0x01);//turn DC Motor B move clockwise
		+	digitalWrite(pinI2,beat&0x02);
		+	digitalWrite(pinI3,beat&0x04);//turn DC Motor A move anticlockwise
		+	digitalWrite(pinI4,beat&0x08);
		+	}
		+
		+	void loop()
		+	{
		+	int i,j;
		+	for(j=0;j<50;j++)
		+	{
		+	for(i=0;i<Beats;i++)
		+	{
		+	beat_control(table[i]);
		+	delay(spead);
		+	}
		+	}
		+	delay(2000);
		+	}
		+
		+	</syntaxhighlight lang="c">

← Older revision		Revision as of 12:16, 24 September 2013
Line 34:		Line 34:
	*8-beat drive: A->AC->C->BC->B->BD->D->AD		*8-beat drive: A->AC->C->BC->B->BD->D->AD

		+	The following shows how to connect the stepper motor to [http://linksprite.com/wiki/index.php5?title=Motor_Shield motor shield].

	[[File:Stepper motor wire.JPG]]		[[File:Stepper motor wire.JPG]]

← Older revision		Revision as of 12:14, 24 September 2013
Line 33:		Line 33:
	*4-beat drive: AC->AD->BD->BC (AC means AC is high level, BD is low level)		*4-beat drive: AC->AD->BD->BC (AC means AC is high level, BD is low level)
	*8-beat drive: A->AC->C->BC->B->BD->D->AD		*8-beat drive: A->AC->C->BC->B->BD->D->AD
		+
		+
		+	[[File:Stepper motor wire.JPG]]

← Older revision		Revision as of 12:13, 24 September 2013
Line 17:		Line 17:
	==Outline==		==Outline==
	[[File:Stepper motor outline.jpg]]		[[File:Stepper motor outline.jpg]]
		+
		+	==Wiring Example==
		+
		+	6-wire 2-phase stepper motor can be used as 4-wire 2-phase stepper motor if the common wire is not used.
		+
		+	For this stepper motor, Red, yellow, black (com) belong to one group. Blue, brown, white (com) belong to the other group.
		+
		+	The definition of wires is as follows:
		+	*Red: A
		+	*Yellow: B
		+	*Blue:C
		+	*Brown:D
		+
		+	There are two modes of driving:
		+	*4-beat drive: AC->AD->BD->BC (AC means AC is high level, BD is low level)
		+	*8-beat drive: A->AC->C->BC->B->BD->D->AD

@@ Line 8: / Line 8: @@
 *6-wire cable attached
 *Rated current: 1.35A
-×Rated voltage: 12V
+*Rated voltage: 12V
 *Winding resistance: 3.3 Ω
 *Size: Length (42mm) x Width (42mm) x Thickness (57mm)