Touch Shield for Arduino - Revision history

Alvin at 12:43, 20 June 2016

2016-06-20T12:43:56Z

2016-06-20T12:35:53Z

2016-06-20T09:55:54Z

2015-09-16T08:14:08Z

2015-09-07T01:46:25Z

‎Introduction

2014-02-18T07:58:40Z

‎How to buy

2013-02-05T02:09:25Z

‎Introduction

2013-02-05T02:08:35Z

‎Introduction

2013-02-05T02:08:21Z

‎Introduction

2012-12-28T07:31:39Z

‎Programming

← Older revision		Revision as of 12:43, 20 June 2016
Line 7:		Line 7:
	[[File:N93DG WITHOUT PACKAGED BACK.jpg\|640px]]		[[File:N93DG WITHOUT PACKAGED BACK.jpg\|640px]]

−	Below photos are for shield without ~~header~~:	+	Below photos are for shield without headers:

← Older revision		Revision as of 12:35, 20 June 2016
Line 7:		Line 7:
	[[File:N93DG WITHOUT PACKAGED BACK.jpg\|640px]]		[[File:N93DG WITHOUT PACKAGED BACK.jpg\|640px]]

−	Below photos are for shield without ~~headers~~:	+	Below photos are for shield without header:

← Older revision		Revision as of 09:55, 20 June 2016
Line 6:		Line 6:

	[[File:N93DG WITHOUT PACKAGED BACK.jpg\|640px]]		[[File:N93DG WITHOUT PACKAGED BACK.jpg\|640px]]
		+
		+	Below photos are for shield without headers:
		+
		+
		+	[[File:Touch Shield for Arduino 001.jpg\|640px]]
		+
		+	[[File:Touch Shield for Arduino 002.jpg\|640px]]
		+
		+	[[File:Touch Shield for Arduino 003.jpg\|640px]]

← Older revision		Revision as of 08:14, 16 September 2015
Line 7:		Line 7:
	[[File:N93DG WITHOUT PACKAGED BACK.jpg\|640px]]		[[File:N93DG WITHOUT PACKAGED BACK.jpg\|640px]]

−	~~[[File:N93DG PACKAGED FRONT.jpg\|640px]]~~

−	~~[[File:N93DG PACKAGED BACK.jpg\|640px]]~~

	== Features ==		== Features ==

@@ Line 3: / Line 3: @@
 The MPR121 IC is a great way to build simple capacitive touch interfaces, and now it's even easier to incorporate into your Arduino projects with the touch shield. The touch shield has 9 capacitive touch pads, with headers for the remaining 3 electrode connections. With this shield you can have a total of 12 touch sensitive buttons. An on-board logic level converter allows it to work with 5V and 3.3V Arduino boards. Simply solder on some header pins and stack it on to your Arduino for a convenient input device. Check below for some example code to get you started.
-[[File:touch_shield.jpg | 400px]]
+[[File:N93DG WITHOUT PACKAGED FRONT.jpg | 640px]]
 == Features  ==

@@ Line 108: / Line 108: @@
 == How to buy  ==
+Here to buy Touch Shield for Arduino on [http://store.linksprite.com/touch-shield-for-arduino/ store]
 == See Also  ==

← Older revision		Revision as of 02:08, 5 February 2013
Line 2:		Line 2:

	The MPR121 IC is a great way to build simple capacitive touch interfaces, and now it's even easier to incorporate into your Arduino projects with the touch shield. The touch shield has 9 capacitive touch pads, with headers for the remaining 3 electrode connections. With this shield you can have a total of 12 touch sensitive buttons. An on-board logic level converter allows it to work with 5V and 3.3V Arduino boards. Simply solder on some header pins and stack it on to your Arduino for a convenient input device. Check below for some example code to get you started.		The MPR121 IC is a great way to build simple capacitive touch interfaces, and now it's even easier to incorporate into your Arduino projects with the touch shield. The touch shield has 9 capacitive touch pads, with headers for the remaining 3 electrode connections. With this shield you can have a total of 12 touch sensitive buttons. An on-board logic level converter allows it to work with 5V and 3.3V Arduino boards. Simply solder on some header pins and stack it on to your Arduino for a convenient input device. Check below for some example code to get you started.
		+
		+	[[File:touchshield.jpg]]

	== Features ==		== Features ==

@@ Line 76: / Line 76: @@
 code procedure:
- init the I2C
+init the I2C
- init MPR121
+init MPR121
- enable the interrupt
+enable the interrupt
 handle the interrupt process,send the data through UART
-notice: The interrupt handle function cannot work with the condition more than two key push down at the same time.
+'''''notice''': The interrupt handle function cannot work with the condition more than two key push down at the same time. ''
-after the initialize
+'''''after the initialize'''''
 [[File:initialize.jpg]]
-The interrupt function send the data to the PC when the key is pressed
+'''''The interrupt function send the data to the PC when the key is pressed'''''
 [[File:interrupt.jpg]]