Difference between revisions of "Quad-band GPRS/GSM Shield for Arduino Mega"
Katherine.d (talk | contribs) (→How to buy) |
(→Hardware Installation) |
||
| Line 55: | Line 55: | ||
=== Hardware Installation === | === Hardware Installation === | ||
| + | ==== Tutorial 1 ==== | ||
| + | Jumpers position: | ||
| + | J1: 5100RX to TX1 | ||
| + | J2: 5100TX to RX1 | ||
| + | |||
| + | Pass through code: | ||
| + | |||
| + | #include //Used for string manipulations | ||
| + | |||
| + | char incoming_char=0; //Will hold the incoming character from the Serial Port. | ||
| + | |||
| + | void setup() | ||
| + | |||
| + | { | ||
| + | |||
| + | //Initialize serial ports for communication. | ||
| + | |||
| + | Serial.begin(9600); | ||
| + | |||
| + | Serial1.begin(9600); | ||
| + | |||
| + | Serial.println("Starting SM5100B Communication..."); | ||
| + | |||
| + | } | ||
| + | |||
| + | void loop() | ||
| + | |||
| + | { | ||
| + | |||
| + | //If a character comes in from the cellular module... | ||
| + | |||
| + | if(Serial1.available() >0) | ||
| + | |||
| + | { | ||
| + | |||
| + | incoming_char=Serial1.read(); //Get the character from the cellular serial port. | ||
| + | |||
| + | Serial.print(incoming_char); //Print the incoming character to the terminal. | ||
| + | |||
| + | } | ||
| + | |||
| + | //If a character is coming from the terminal to the Arduino... | ||
| + | |||
| + | if(Serial.available() >0) | ||
| + | |||
| + | { | ||
| + | |||
| + | incoming_char=Serial.read(); //Get the character coming from the terminal | ||
| + | |||
| + | Serial1.print(incoming_char); //Send the character to the cellular module. | ||
| + | |||
| + | } | ||
| + | |||
| + | } | ||
=== Programming === | === Programming === | ||
Revision as of 08:33, 13 December 2012
Contents
Introduction
Model:ARDUI_MEGA_5100_GPRS
Features
Application Ideas
Cautions
Schematic
Specification
Pin definition and Rating
Mechanic Dimensions
Usage
Hardware Installation
Tutorial 1
Jumpers position:
J1: 5100RX to TX1
J2: 5100TX to RX1
Pass through code:
- include //Used for string manipulations
char incoming_char=0; //Will hold the incoming character from the Serial Port.
void setup()
{
//Initialize serial ports for communication.
Serial.begin(9600);
Serial1.begin(9600);
Serial.println("Starting SM5100B Communication...");
}
void loop()
{
//If a character comes in from the cellular module...
if(Serial1.available() >0)
{
incoming_char=Serial1.read(); //Get the character from the cellular serial port.
Serial.print(incoming_char); //Print the incoming character to the terminal.
}
//If a character is coming from the terminal to the Arduino...
if(Serial.available() >0)
{
incoming_char=Serial.read(); //Get the character coming from the terminal
Serial1.print(incoming_char); //Send the character to the cellular module.
}
}
Programming
FAQ
Please list your question here:
Support
If you have questions or other better design ideas, you can go to our forum to discuss or creat a ticket for your issue at linksprite support.
Resources
How to buy
Here to buy Quad-band GPRS/GSM Shield for Arduino MegaARDUI_MEGA_5100_GPRS on LinkSprite Cart
See Also
Other related products and resources.
Licensing
This documentation is licensed under the Creative Commons Attribution-ShareAlike License 3.0 Source code and libraries are licensed under GPL/LGPL, see source code files for details.
