Difference between revisions of "3mm Yellow LED Module"
Qian.zhang (talk | contribs) (Created page with "==Introduction== Linker LED Module is designed for the beginners of Arduino/pcDuino to monitor controls from digital ports. It can be mounted to the surface of your box or de...") |
(→Introduction) |
||
| (10 intermediate revisions by 2 users not shown) | |||
| Line 2: | Line 2: | ||
Linker LED Module is designed for the beginners of Arduino/pcDuino to monitor controls from digital ports. It can be mounted to the surface of your box or desk easily and used as pilot lamp for power or signal. Its brightness can be adjust by potentiometer. | Linker LED Module is designed for the beginners of Arduino/pcDuino to monitor controls from digital ports. It can be mounted to the surface of your box or desk easily and used as pilot lamp for power or signal. Its brightness can be adjust by potentiometer. | ||
| − | [[File: | + | |
| + | |||
| + | |||
| + | [[File:Yellow LED-118101001-1 first.jpg| 640px]] | ||
| + | |||
| + | [[File:Yellow LED-118101001-1 second.jpg| 640px]] | ||
| + | |||
| + | [[File:Yellow LED-118101001-1 third.jpg| 640px]] | ||
| + | |||
| + | == Features == | ||
| + | |||
| + | Dimensions: 23.0×24.2×9.5mm | ||
| + | |||
| + | Net weight: 1.8g | ||
| + | |||
| + | == Dimension == | ||
| + | |||
| + | [[File:led 3mm dimension.jpg]] | ||
| + | |||
| + | ==Schematics== | ||
| + | |||
| + | *[https://s3.amazonaws.com/linksprite/LinkerKit/Linker_LED.pdf Schematics] | ||
| + | |||
| + | ==Application Ideas== | ||
| + | |||
| + | '''test''' | ||
| + | <syntaxhighlight lang="c"> | ||
| + | /* | ||
| + | Blink | ||
| + | Turns on an LED on for one second, then off for one second, repeatedly. | ||
| + | |||
| + | This example code is in the public domain. | ||
| + | */ | ||
| + | |||
| + | void setup() { | ||
| + | // initialize the digital pin as an output. | ||
| + | pinMode(13, OUTPUT); | ||
| + | } | ||
| + | |||
| + | void loop() { | ||
| + | digitalWrite(13, HIGH); // set the LED on | ||
| + | delay(1000); // wait for a second | ||
| + | digitalWrite(13, LOW); // set the LED off | ||
| + | delay(1000); // wait for a second | ||
| + | } | ||
| + | </syntaxhighlight> | ||
| + | |||
| + | [[File:yellow flash.jpg]] | ||
Latest revision as of 09:28, 15 July 2016
Introduction
Linker LED Module is designed for the beginners of Arduino/pcDuino to monitor controls from digital ports. It can be mounted to the surface of your box or desk easily and used as pilot lamp for power or signal. Its brightness can be adjust by potentiometer.
Features
Dimensions: 23.0×24.2×9.5mm
Net weight: 1.8g
Dimension
Schematics
Application Ideas
test <syntaxhighlight lang="c"> /*
Blink Turns on an LED on for one second, then off for one second, repeatedly. This example code is in the public domain. */
void setup() {
// initialize the digital pin as an output. pinMode(13, OUTPUT);
}
void loop() {
digitalWrite(13, HIGH); // set the LED on delay(1000); // wait for a second digitalWrite(13, LOW); // set the LED off delay(1000); // wait for a second
} </syntaxhighlight>
