Difference between revisions of "Starter Kit for Arduino ---Beginner Full Package"
(→Introduction) |
(→Package List) |
||
Line 7: | Line 7: | ||
==Package List== | ==Package List== | ||
− | *1 | + | *1 x Cuteduino: An Arduino Uno R3 compatible board. |
− | *1 | + | *1 x USB A to B cable |
− | *1 | + | *1 x Mini Breadboard |
− | * | + | *40 x Male to male jumper wire: These are high quality wires that allow you to connect the female headers on the Arduino to the components and breadboard. 40 4" wires, 10 6", and 10 9" wires. |
− | *2 | + | *2 x Tri-Color LED: Because everyone loves a blinky. Use this LED to PWM mix any color you need. |
− | *2 | + | *2 x Red LEDs: Light emitting diodes make great general indicators. |
− | *2 | + | *2 x Green LEDs:Light emitting diodes make great general indicators |
− | *2 | + | *2 x Blue LEDs: Light emitting diodes make great general indicators. |
− | *2 | + | *2 x Buttons: To interface with outside world |
− | *2 | + | *2 x Photocell: - A sensor to detect ambient light. Perfect for detecting when a drawer is opened or when night-time approaches. |
− | *2 | + | *2 x Thermistor - A sensor for detecting ambient temperature and temperature changes. 10K thermistor with a negative temperature coefficient. |
− | *2 | + | *2 x Potentiometer: 2 adjustable 10K ohm potentiometer can be used to do ADC input experiments. |
− | *5 | + | *5 x 300 Ohm Resistors - 5 current limiting resistors for LEDs, and strong pull-up resistors. |
− | *5 | + | *5 x 1k Ohm Resistors - 5 current limiting resistors for LEDs, and strong pull-up resistors. |
− | *5 | + | *5 x 5K Ohm Resistors - 5 current limiting resistors for LEDs, and strong pull-up resistors. |
− | *1 | + | *1 x Buzzer |
Revision as of 07:37, 6 April 2016
Introduction
This is a starter kit for Arduino beginner.
Package List
- 1 x Cuteduino: An Arduino Uno R3 compatible board.
- 1 x USB A to B cable
- 1 x Mini Breadboard
- 40 x Male to male jumper wire: These are high quality wires that allow you to connect the female headers on the Arduino to the components and breadboard. 40 4" wires, 10 6", and 10 9" wires.
- 2 x Tri-Color LED: Because everyone loves a blinky. Use this LED to PWM mix any color you need.
- 2 x Red LEDs: Light emitting diodes make great general indicators.
- 2 x Green LEDs:Light emitting diodes make great general indicators
- 2 x Blue LEDs: Light emitting diodes make great general indicators.
- 2 x Buttons: To interface with outside world
- 2 x Photocell: - A sensor to detect ambient light. Perfect for detecting when a drawer is opened or when night-time approaches.
- 2 x Thermistor - A sensor for detecting ambient temperature and temperature changes. 10K thermistor with a negative temperature coefficient.
- 2 x Potentiometer: 2 adjustable 10K ohm potentiometer can be used to do ADC input experiments.
- 5 x 300 Ohm Resistors - 5 current limiting resistors for LEDs, and strong pull-up resistors.
- 5 x 1k Ohm Resistors - 5 current limiting resistors for LEDs, and strong pull-up resistors.
- 5 x 5K Ohm Resistors - 5 current limiting resistors for LEDs, and strong pull-up resistors.
- 1 x Buzzer