Difference between revisions of "JPEG 2M Pixel Color Camera Serial Interface(TTL level)"
Katherine.d (talk | contribs) |
Katherine.d (talk | contribs) |
||
Line 39: | Line 39: | ||
'''''Arduino sample code provided''''' | '''''Arduino sample code provided''''' | ||
<syntaxhighlight lang="c"> | <syntaxhighlight lang="c"> | ||
+ | /* Linksprite */ | ||
+ | |||
+ | #include <NewSoftSerial.h> | ||
+ | |||
+ | byte incomingbyte; | ||
+ | NewSoftSerial mySerial(4,5); //Configure pin 4 and 5 as soft serial port | ||
+ | int a=0x0000,j=0,k=0,count=0; //Read Starting address | ||
+ | uint8_t MH,ML; | ||
+ | boolean EndFlag=0; | ||
+ | |||
+ | void SendResetCmd(); | ||
+ | void SendTakePhotoCmd(); | ||
+ | void SendReadDataCmd(); | ||
+ | void StopTakePhotoCmd(); | ||
+ | |||
+ | void setup() | ||
+ | { | ||
+ | Serial.begin(19200); | ||
+ | mySerial.begin(38400); | ||
+ | } | ||
+ | |||
+ | void loop() | ||
+ | { | ||
+ | SendResetCmd(); | ||
+ | delay(4000); //After reset, wait 2-3 second to send take picture command | ||
+ | |||
+ | SendTakePhotoCmd(); | ||
+ | |||
+ | while(mySerial.available()>0) | ||
+ | { | ||
+ | incomingbyte=mySerial.read(); | ||
+ | |||
+ | } | ||
+ | byte a[32]; | ||
+ | |||
+ | while(!EndFlag) | ||
+ | { | ||
+ | j=0; | ||
+ | k=0; | ||
+ | count=0; | ||
+ | SendReadDataCmd(); | ||
+ | |||
+ | delay(25); | ||
+ | while(mySerial.available()>0) | ||
+ | { | ||
+ | incomingbyte=mySerial.read(); | ||
+ | k++; | ||
+ | if((k>5)&&(j<32)&&(!EndFlag)) | ||
+ | { | ||
+ | a[j]=incomingbyte; | ||
+ | if((a[j-1]==0xFF)&&(a[j]==0xD9)) //Check if the picture is over | ||
+ | EndFlag=1; | ||
+ | j++; | ||
+ | count++; | ||
+ | } | ||
+ | } | ||
+ | |||
+ | for(j=0;j<count;j++) | ||
+ | { if(a[j]<0x10) | ||
+ | Serial.print("0"); | ||
+ | Serial.print(a[j],HEX); | ||
+ | Serial.print(" "); | ||
+ | } //Send jpeg picture over the serial port | ||
+ | Serial.println(); | ||
+ | } | ||
+ | while(1); | ||
+ | } | ||
+ | |||
+ | //Send Reset command | ||
+ | void SendResetCmd() | ||
+ | { | ||
+ | mySerial.print(0x56, BYTE); | ||
+ | mySerial.print(0x00, BYTE); | ||
+ | mySerial.print(0x26, BYTE); | ||
+ | mySerial.print(0x00, BYTE); | ||
+ | } | ||
+ | |||
+ | //Send take picture command | ||
+ | void SendTakePhotoCmd() | ||
+ | { | ||
+ | mySerial.print(0x56, BYTE); | ||
+ | mySerial.print(0x00, BYTE); | ||
+ | mySerial.print(0x36, BYTE); | ||
+ | mySerial.print(0x01, BYTE); | ||
+ | mySerial.print(0x00, BYTE); | ||
+ | } | ||
+ | |||
+ | //Read data | ||
+ | void SendReadDataCmd() | ||
+ | { | ||
+ | MH=a/0x100; | ||
+ | ML=a%0x100; | ||
+ | mySerial.print(0x56, BYTE); | ||
+ | mySerial.print(0x00, BYTE); | ||
+ | mySerial.print(0x32, BYTE); | ||
+ | mySerial.print(0x0c, BYTE); | ||
+ | mySerial.print(0x00, BYTE); | ||
+ | mySerial.print(0x0a, BYTE); | ||
+ | mySerial.print(0x00, BYTE); | ||
+ | mySerial.print(0x00, BYTE); | ||
+ | mySerial.print(MH, BYTE); | ||
+ | mySerial.print(ML, BYTE); | ||
+ | mySerial.print(0x00, BYTE); | ||
+ | mySerial.print(0x00, BYTE); | ||
+ | mySerial.print(0x00, BYTE); | ||
+ | mySerial.print(0x20, BYTE); | ||
+ | mySerial.print(0x00, BYTE); | ||
+ | mySerial.print(0x0a, BYTE); | ||
+ | a+=0x20; //address increases 32,set according to buffer size | ||
+ | } | ||
+ | |||
+ | void StopTakePhotoCmd() | ||
+ | { | ||
+ | mySerial.print(0x56, BYTE); | ||
+ | mySerial.print(0x00, BYTE); | ||
+ | mySerial.print(0x36, BYTE); | ||
+ | mySerial.print(0x01, BYTE); | ||
+ | mySerial.print(0x03, BYTE); | ||
+ | } | ||
+ | |||
+ | </syntaxhighlight> | ||
== Support == | == Support == |
Revision as of 09:27, 25 February 2013
Contents
Description
LS-Y201-2MP is LinkSprite’s new generation high resolution serial port camera module. Its resolution is 2 million pixel. It can captures high resolution pictures using the serial port. LS-Y201-2MP is a modular design that outputs JPEG images through UART, and can be easily integrated into existing design.
Specification
- 2 Million Pixels
- Support capture JPEG from serial port
- Default baud rate of serial port is 38400
- DC 3.3V or 5V power supply
- Size 32mm X 32mm
- Current consumption: 80-100mA
- The pin near C03 is AV output pin, which is an analog output pin.
Application Idea
- Different image capture systems
- Environmental monitoring
- Industry monitoring
- Medical equipment
- Video phone
- Security
- Vehicle based GPS
Usage
Hardware Installation
Evaluation Setup
Programming
- Step 1: Click Open COM
- Step 2: Click Single Shot.
Arduino sample code provided <syntaxhighlight lang="c"> /* Linksprite */
- include <NewSoftSerial.h>
byte incomingbyte; NewSoftSerial mySerial(4,5); //Configure pin 4 and 5 as soft serial port int a=0x0000,j=0,k=0,count=0; //Read Starting address uint8_t MH,ML; boolean EndFlag=0;
void SendResetCmd(); void SendTakePhotoCmd(); void SendReadDataCmd(); void StopTakePhotoCmd();
void setup() {
Serial.begin(19200); mySerial.begin(38400);
}
void loop() {
SendResetCmd(); delay(4000); //After reset, wait 2-3 second to send take picture command SendTakePhotoCmd();
while(mySerial.available()>0) { incomingbyte=mySerial.read();
} byte a[32]; while(!EndFlag) { j=0; k=0; count=0; SendReadDataCmd();
delay(25); while(mySerial.available()>0) { incomingbyte=mySerial.read(); k++; if((k>5)&&(j<32)&&(!EndFlag)) { a[j]=incomingbyte; if((a[j-1]==0xFF)&&(a[j]==0xD9)) //Check if the picture is over EndFlag=1; j++;
count++;
} } for(j=0;j<count;j++) { if(a[j]<0x10) Serial.print("0"); Serial.print(a[j],HEX); Serial.print(" "); } //Send jpeg picture over the serial port Serial.println(); } while(1);
}
//Send Reset command void SendResetCmd() {
mySerial.print(0x56, BYTE); mySerial.print(0x00, BYTE); mySerial.print(0x26, BYTE); mySerial.print(0x00, BYTE);
}
//Send take picture command void SendTakePhotoCmd() {
mySerial.print(0x56, BYTE); mySerial.print(0x00, BYTE); mySerial.print(0x36, BYTE); mySerial.print(0x01, BYTE); mySerial.print(0x00, BYTE);
}
//Read data void SendReadDataCmd() {
MH=a/0x100; ML=a%0x100; mySerial.print(0x56, BYTE); mySerial.print(0x00, BYTE); mySerial.print(0x32, BYTE); mySerial.print(0x0c, BYTE); mySerial.print(0x00, BYTE); mySerial.print(0x0a, BYTE); mySerial.print(0x00, BYTE); mySerial.print(0x00, BYTE); mySerial.print(MH, BYTE); mySerial.print(ML, BYTE); mySerial.print(0x00, BYTE); mySerial.print(0x00, BYTE); mySerial.print(0x00, BYTE); mySerial.print(0x20, BYTE); mySerial.print(0x00, BYTE); mySerial.print(0x0a, BYTE); a+=0x20; //address increases 32,set according to buffer size
}
void StopTakePhotoCmd() {
mySerial.print(0x56, BYTE); mySerial.print(0x00, BYTE); mySerial.print(0x36, BYTE); mySerial.print(0x01, BYTE); mySerial.print(0x03, BYTE);
}
</syntaxhighlight>
Support
If you have questions or other better design ideas, you can go to our forum to discuss or creat a ticket for your issue at linksprite support.
Resources
- Evaluation Software
- Linksprite Open Source Code for X86
- .Net micro framework source code
- Github
- Tutorial at Linksprite
How to buy
Here to buy on LinkSprite Cart