3G + GPS Shield for Arduino
Contents
Introduction
The new 3G shield for Arduino enables the connectivity to high speed WCDMA and HSPA cellular networks in order to make possible the creation of the next level of worldwide interactivity projects inside the new "Internet of Things" era.
The module counts also with an internal GPS what enables the location of the device outdoors and indoors combining standard NMEA frames with mobile cell ID triangulation using both assisted-mobile (A-GPS) and mobile-based (S-GPS) modes.
Other interesting accessories which can be connected to the module are a video camera which enables the record of video in high resolution (640x480), an audio kit including microphone, speaker, hands free and headphones sets and a SD socket to save directly all the data coming from the 3G network or recorded from the video camera. You can even reproduce audio files stored in the SD card (like a mp3 player!).
You can also use it as a standard 3G modem at full speed (~7.2Mbps download, ~5.5Mbps upload) just connecting it through its specific mini-USB socket to your laptop (Linux, Windows, MacOS).
The new communicating module is specially oriented to work with Internet servers implementing internally several application layer protocols which make easier to send the information to the cloud. We can make HTTP and HTTPS (secure mode) navigation, downloading and uploading content to a web server. In the same way FTP and FTPS (secure mode) protocols are also available which is really useful when your application requires handling files. You can even send and receive mails directly from Arduino using the SMTP and POP3 clients implemented internally.
With the SD Card socket so you can handle a complete FAT16 file systems and store up to 32GB of information. This specially useful as the 3G module can work at full speed (~7.2Mbps download, ~5.5Mbps upload) when working with the SD files directly without need of Arduino for data or files management.
The GPS module also makes possible perform geolocation services even in indoors as it can work in A-GPS and S-GPS modes, so the location given by the GPS through NMEA sentences is completed with the cell information provided by both the 3G module and external Internet Geoposition Servers which helps you to get the most accurate location in each case.
Features
- WCDMA and HSPA 3G networks compatibility
- Internal GPS for Assisted A-GPS and Supported S-GPS modes
- Video Camera (640x480) for video and photo recordings available
- Audio Kit including microphone, speaker, hands free and headphones available
- SD file system up to 32GB
- Works as a standard 3G modem in Linux/Windows/MacOS (~7.2Mbps download, ~5.5Mbps upload)
- Talk directly to web servers by HTTP/HTTPS (secure)
- Upload and download files directly by FTP/FTPS (secure)
- Send and receive mails by POP3/SMTP
- Play compressed audio files
Antennas
Connections
SIM5218 has 3 UFL connectors. Two for diversity of 3G mobile carriers and one for GPS antenna. The impedance of the RF interface is 50Ω. It is recommended use just the "main" antenna socket for the mobile connection unless you experience coverage or performance problems. In this case two antennas allowing diversity may be placed.
Also, the module allows to solder the antenna to the pad, or attach it via contact springs.
Bandwidth
3G module connected with Arduino allows downlinks rates over 115200 bauds (~11.5KBps), the maximum UART's speed and uplinks rates over 30000 bauds (~3KBps).
Using the module as 3G USB modem we got speeds of 2Mbps (~222KBps) for downlink and 0.7Mbps (~77KBps) for uplink and.
The connection speed may vary depending on the state of the network, the quality of the signal and the carrier.
Using 3G module with AT commands
Important issues:
- Use capital letters for AT commands.
- Send CR (Carriage return) and LF (Line feed) after the AT command.
- Place the serial communication jumpers in the right position.
- Use an external power supply and place the power jumpers in the right position. If the shield is powered from the Arduino, the power jumper must be in Arduino 5V position. If the shield is powered from the Vin input (in the shield), the power jumper must be in Vext position.
The first thing we are going to do with the module is to connect the module to a PC directly (using an Arduino as gateway) and check the basic AT commands. In this case, serial communication jumpers have to be set on USB gateway position.
Remember take out the ATmega microcontroller from the Arduino gateway.
Basic configuration:
Connect the shield to the Arduino gateway.
Then connect the SIM card and the USB cable.
Finally plug the USB cable to the computer and open a serial port terminal to communicate via the usb port (e.g: hyperterminal (win), cutecom / gtkterm (linux)).
If you use the Arduino IDE serial monitor for sending AT commands – Be sure that you are sending CR (Carriage return) and LF (Line Feed).
Set the baudrate to 115200 bps and open the serial port, then press the ON button for two seconds. Then if you type AT you'll get OK, this means that the communication with the module is working fine. Now, with the module working you can check some AT commands to control the module, the basic commands are:
Important type commands in capital letters and with CR (carriage return) and LF (line feed)!!!
| Command | Respone | Description |
|---|---|---|
| AT | OK | If you get OK, the communication with the module is working |
| AT+CPIN="****" | OK | If the SIM card is locked with PIN (**** is the pin number) |
| AT+COPS? | Operator information |
NOTE: If your 3G module doesn't answer to AT commands, maybe it is configured in a different baudrate. The command for change it temporally is AT+IPR. Try differents baudrates (300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200, 230400, 460800,921600, 3200000,3686400,4000000 ) until you get to communicate. Once you can communicate, you can configure it in the baudrate you want.
Using 3G module like a modem
If you want to use the 3G module such a modem, please refer to the next link:
[3G modem tutorial]
Audio
Audio Features
SIM5218 module provides two analogy inputs for microphone and three analogy outputs for two speakers and headphones. Depending of the selected audio channel (normal, headset and hands-free) a specific input and output are activated. The different channels are selected with the command AT+CSDVC.
Normal channel (AT+CSDVC=1) uses the main microphone and a speaker. Headset channel (AT+CSDVC=2) uses the jack connector. Hand-free channel (AT+CSDVC=3) uses the main microphone and the loudspeaker.
Both microphones don't need an external power source because they are powered directly by the module. You can use some extra commands in your codes like noise suppression, echo canceller or the gain of the mic amps. Please, refer to the AT command document list at the end of this article for more information.
Audio Connectors
Audio connectors are situated at the bottom of the board. The two speakers and the main microphone are connected to board using pin connectors.
Headset connector are situated at the bottom too, between Arduino board and 3G board.
This connector has 4 terminals that correspond with the positive terminal of the microphone, left and rigth headphones and common ground. The order of connections show below.
Originating and receiving voice calls
The code example and the connection diagram shown below are used to originate a voice call and, pushing a button, end that voice call. The button is connected between digital pin 12 an ground. A 10kΩ pull-up resistor is needed at this pin.
<syntaxhighlight lang="c"> /*
- This program is free software: you can redistribute it and/or modify
- it under the terms of the GNU General Public License as published by
- the Free Software Foundation, either version 3 of the License, or
- (at your option) any later version.
- This program is distributed in the hope that it will be useful,
- but WITHOUT ANY WARRANTY; without even the implied warranty of
- MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- GNU General Public License for more details.
- You should have received a copy of the GNU General Public License
- along with this program. If not, see .
- Version 0.1
- /
int led = 13;
int button = 12;
int onModulePin = 2; // the pin to switch on the module (without press on button)
int timesToSend = 1; // Numbers of calls to make
char phone_number[]="*********"; // ********* is the number to call
void switchModule(){
digitalWrite(onModulePin,HIGH); delay(2000); digitalWrite(onModulePin,LOW);
}
void setup(){
Serial.begin(115200); // UART baud rate delay(2000); pinMode(button, INPUT); pinMode(led, OUTPUT); pinMode(onModulePin, OUTPUT); switchModule(); // switches the module ON
for (int i=0;i < 5;i++){
delay(5000);
}
}
void loop(){
while (count < timesToSend){
for(int x=0;x < 9;x++){ //generates the tones of the phone number
Serial.print("AT+CPTONE=");
Serial.println(phone_number[x]);
delay(400);
}
Serial.print("ATD");
Serial.print(phone_number);
Serial.println(";");
while(digitalRead(button)==1);
Serial.println("AT+CHUP"); // disconnects the existing call
delay(5000);
count++; }
}
</syntaxhighlight>
To make a lost call next code is used.
<syntaxhighlight lang="c"> /*
- This program is free software: you can redistribute it and/or modify
- it under the terms of the GNU General Public License as published by
- the Free Software Foundation, either version 3 of the License, or
- (at your option) any later version.
- This program is distributed in the hope that it will be useful,
- but WITHOUT ANY WARRANTY; without even the implied warranty of
- MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- GNU General Public License for more details.
- You should have received a copy of the GNU General Public License
- along with this program. If not, see .
- Version 0.1
- /
int led = 13;
int onModulePin = 2; // the pin to switch on the module (without press on button)
int timesToSend = 1; // Numbers of calls to make int count = 0; int tones = 2; //Each tone has a duration of 6 seconds aprox.
char phone_number[]="*********"; // ********* is the number to call
void switchModule(){
digitalWrite(onModulePin,HIGH); delay(2000); digitalWrite(onModulePin,LOW);
}
void setup(){
Serial.begin(115200); // UART baud rate delay(2000); pinMode(led, OUTPUT); pinMode(onModulePin, OUTPUT); switchModule(); // switches the module ON
for (int i=0;i < 5;i++){
delay(5000);
}
}
void loop(){
while (count < timesToSend){
delay(1500);
for(int x=0;x < 9;x++){ //generates the tones of the phone number
Serial.print("AT+CPTONE=");
Serial.println(phone_number[x]);
delay(400);
}
Serial.print("ATD");
Serial.print(phone_number);
Serial.println(";");
delay(6000*tones);
Serial.println("AT+CHUP"); // cancel the call
delay(5000);
count++; }
} </syntaxhighlight>
To receive calls the used code are this and the connection diagram is the same that the used to originate calls. Don't forget the pull-up resistor on pin 12.
<syntaxhighlight lang="c"> /*
- This program is free software: you can redistribute it and/or modify
- it under the terms of the GNU General Public License as published by
- the Free Software Foundation, either version 3 of the License, or
- (at your option) any later version.
- This program is distributed in the hope that it will be useful,
- but WITHOUT ANY WARRANTY; without even the implied warranty of
- MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- GNU General Public License for more details.
- You should have received a copy of the GNU General Public License
- along with this program. If not, see .
- Version 0.1
- /
int led = 13;
int button = 12;
int onModulePin = 2; // the pin to switch on the module (without press on button)
int timesToSend = 1; // Numbers of calls to make
void switchModule(){
digitalWrite(onModulePin,HIGH); delay(2000); digitalWrite(onModulePin,LOW);
}
boolean check_response(char *str){
int i = 0; int j = 0; char b[10];
// reading the message and cutting
// initials and finals
while(Serial.available() > 0){
if(j==0 || j==1){
Serial.read();
j++;
}
else if( Serial.peek() == 13 ){
b[i] = 0;
Serial.read();
}
else if( Serial.peek() == 10 ){
Serial.read();
}
else {
b[i++] = Serial.read();
}
}
// comparing
int cont=0;
int cont2=0;
boolean ok=false;
while(b[cont]!=-1){
if (b[cont]==str[cont2]){
while(str[cont2]!=-1){
if (b[cont+cont2]!=b[cont2])
{
cont2++;
ok=true;
}
else {
ok=false;
break;
}
}
}
if (ok) break;
cont++;
}
if(ok){
return true;
}
return false;
}
void setup(){
Serial.begin(115200); // UART baud rate delay(2000); pinMode(button, INPUT); pinMode(led, OUTPUT); pinMode(onModulePin, OUTPUT); switchModule(); // switches the module ON
for (int i=0;i < 5;i++){
delay(5000);
}
}
void loop(){
while(!check_response("RING")); //waits for a call
Serial.println("ATA"); //answers an incoming call
delay(10000);
while(digitalRead(button)==1);
Serial.println("AT+CHUP"); // disconnects the existing call
} </syntaxhighlight>
The channel may be changed during a call. Use the command AT+CSDVC to select the channel that you want.
Recording and playing sound
With the next code we can record a sound, stores it and before play it. You can select the place to store the sound clip: the local storage or a SD card. Once saved the sound can be sent to an FTP or FTPS as you'll see later.
<syntaxhighlight lang="c"> /*
- This program is free software: you can redistribute it and/or modify
- it under the terms of the GNU General Public License as published by
- the Free Software Foundation, either version 3 of the License, or
- (at your option) any later version.
- This program is distributed in the hope that it will be useful,
- but WITHOUT ANY WARRANTY; without even the implied warranty of
- MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- GNU General Public License for more details.
- You should have received a copy of the GNU General Public License
- along with this program. If not, see .
- Version 0.1
- /
int led = 13;
int onModulePin = 2; // the pin to switch on the module (without press on button)
int x = 0;
char name[20];
void switchModule(){
digitalWrite(onModulePin,HIGH); delay(2000); digitalWrite(onModulePin,LOW);
}
void setup(){
for(x=0;x < 20;x++){
name[x]='\0';
}
Serial.begin(115200); // UART baud rate delay(2000); pinMode(led, OUTPUT); pinMode(onModulePin, OUTPUT); switchModule(); // switches the module ON
for (int i=0;i < 5;i++){
delay(5000);
}
Serial.println("AT+FSLOCA=0");
// store media files to local storage space, put 1 to store media files to storage card
while(Serial.read()!='K');
Serial.println("AT+CNSM=1"); // Enables noise supression
while(Serial.read()!='K');
}
void loop(){
//RECORDING A SOUND CLIP
delay(1500);
while(Serial.available()!=0){
Serial.read();
}
Serial.println("AT+CQCPREC=0,amr"); // starts to record a sound clip
Serial.flush();
while(Serial.read()!='/');
while(Serial.read()!='/');
x=0;
do{
while(Serial.available()==0);
name[x]=Serial.read();
x++;
}while(x < 19);
while(Serial.read()!='K'); Serial.println(name); delay(10000);
Serial.println("AT+CQCPPAUSE"); // pauses record sound
while(Serial.read()!='K');
delay(2000);
Serial.println("AT+CQCPRESUME"); // resumes record sound
while(Serial.read()!='K');
delay(10000);
Serial.println("AT+CQCPSTOP"); // stops to record a sound clip
while(Serial.read()!='K');
//PLAY A SOUND CLIP
Serial.println("AT+FSCD=Audio");
Serial.flush();
while(Serial.read()!='K');
Serial.print("AT+CCMXPLAY=\""); //plays an audio file
Serial.print(name);
Serial.println("\"");
Serial.flush();
while(Serial.read()!='K');
delay(7000);
Serial.println("AT+CCMXPAUSE"); // pauses playing audio file
while(Serial.read()!='K');
delay(2000);
Serial.println("AT+CCMXRESUME"); // resumes playing audio file
while(Serial.read()!='K');
delay(8000);
Serial.println("AT+CCMXSTOP"); // Stops playing audio file
while(Serial.read()!='K');
while(1);
} </syntaxhighlight>
Also, you can use the 3G module like a mp3 player! First, you must save your music in mp3, amr or qcp format. You can use Audacity (linux) or Mobile Media Converter (Windows or Linux) to do this. Then, save the music in the Audio folder on microSD card. Now, put microSD card into the shield and enjoy the music!
NOTE: You will need to update your firmware to play mp3. The update is available here. Uncompress and run it in a PC with Windows (emulated Windows not supported).
A voice call can be recorded using these same commands too.
Command summary
| Command | Response | Description |
|---|---|---|
| AT+CPTONE=** | OK | Plays a DTMF tone or complex tone on local voice channel device . ** is the number of the tone. |
| ATD*********; | ********* is the number to call. | |
| ATA | OK | Answer an incoming call. |
| AT+CHUP | OK | Cancel voice calls. |
| AT+CNSM | OK | Enable/disable noise suppression. |
| AT+CQCPREC=*,&&& | Starts recording sound clips . Answers with the path and the name of the clip. * is the path and &&& is the format. | |
| AT+CQCPPAUSE | OK | Pauses record sound. |
| AT+CQCPRESUME | OK | Resumes record sound. |
| AT+CQCPSTOP | OK | Stops record sound. |
| AT+CCMXPLAY=”*****” | OK | Plays an audio file . ***** is the name of the file. |
| AT+CCMXPAUSE | OK | Pauses playing audio file. |
| AT+CCMXRESUME | OK | Resumes playing audio file. |
| AT+CCMXSTOP | OK | Stops playing audio file. |
Camera
| Pin nº | Name | Pin nº | Name | Pin nº | Name |
|---|---|---|---|---|---|
| 1 | NC | 9 | HSYNC | 17 | PCLK |
| 2 | AGND | 10 | DVDD | 18 | DATA6 |
| 3 | SDA | 11 | DOVDD | 19 | DATA2 |
| 4 | AVDD | 12 | DATA9 | 20 | DATA5 |
| 5 | SCL | 13 | MCLK | 21 | DATA3 |
| 6 | RESET | 14 | DATA8 | 22 | DATA22 |
| 7 | VSYNC | 15 | AGND | 23 | DATA1 |
| 8 | PWDN | 16 | DATA7 | 24 | DATA0 |
Mounting the camera
Follow these simple steps to mount the camera into the 3G Arduino board.
- The first step is to open the socket. To do this, pull carefully out the sides of the connector.
- Inserts the camera with metallic contacts facing up
- At the final step, push in the laterals of the connector
Vedio Recording
To record video, and take images, you must start the camera in the first step. After you can configure some parameters like resolution, fps, rotation or zoom. The next code allows to record a video file in mp4 format. Remember, if you want to store the video file in a SD card, you must to use AT+FSLOCA command.
<syntaxhighlight lang="c"> /*
- This program is free software: you can redistribute it and/or modify
- it under the terms of the GNU General Public License as published by
- the Free Software Foundation, either version 3 of the License, or
- (at your option) any later version.
- This program is distributed in the hope that it will be useful,
- but WITHOUT ANY WARRANTY; without even the implied warranty of
- MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- GNU General Public License for more details.
- You should have received a copy of the GNU General Public License
- along with this program. If not, see .
- Version 0.1
- /
int led = 13;
int onModulePin = 2; // the pin to switch on the module (without press on button)
int x = 0;
char name[20];
void switchModule(){
digitalWrite(onModulePin,HIGH); delay(2000); digitalWrite(onModulePin,LOW);
}
void setup(){
Serial.begin(115200); //UART baud rate delay(2000); pinMode(led, OUTPUT); pinMode(onModulePin, OUTPUT); switchModule(); // switches the module ON
for (int i=0;i < 5;i++){
delay(5000);
}
Serial.println("AT+CCAMS"); //starts the camera
while(Serial.read()!='K');
Serial.println("AT+CCAMSETD=320,240"); //sets QVGA (320*240) resolution
while(Serial.read()!='K');
Serial.println("AT+CCAMSETF=2"); //sets 15 frames per second
while(Serial.read()!='K');
}
void loop(){
delay(1500);
while(Serial.available()!=0){
Serial.read();
}
Serial.println("AT+CCAMRS"); //starts to record a video
Serial.flush(); //video is saved into C:/Video
while(Serial.read()!='/');
while(Serial.read()!='/');
x=0;
do{
while(Serial.available()==0);
name[x]=Serial.read();
x++;
}while(x < 19);
while(Serial.read()!='K'); Serial.println(name); delay(10000);
Serial.println("AT+CCAMRP"); // pauses record
while(Serial.read()!='K');
delay(2000);
Serial.println("AT+CCAMRR"); // resumes record
while(Serial.read()!='K');
delay(10000);
Serial.println("AT+CCAMRE"); // stops to record
while(Serial.read()!='K');
Serial.println("AT+CCAME"); // stops the camera
while(Serial.read()!='K');
while(1);
} </syntaxhighlight>
Taking Photo
Take photos is very easy, here is the example code:
<syntaxhighlight lang="c"> /*
- This program is free software: you can redistribute it and/or modify
- it under the terms of the GNU General Public License as published by
- the Free Software Foundation, either version 3 of the License, or
- (at your option) any later version.
- This program is distributed in the hope that it will be useful,
- but WITHOUT ANY WARRANTY; without even the implied warranty of
- MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- GNU General Public License for more details.
- You should have received a copy of the GNU General Public License
- along with this program. If not, see .
- Version 0.1
- /
int led = 13;
int onModulePin = 2; // the pin to switch on the module (without press on button)
int x = 0;
char name[20];
void switchModule(){
digitalWrite(onModulePin,HIGH); delay(2000); digitalWrite(onModulePin,LOW);
}
void setup(){
Serial.begin(115200); // UART baud rate delay(2000); pinMode(led, OUTPUT); pinMode(onModulePin, OUTPUT); switchModule(); // switches the module ON
for (int i=0;i < 5;i++){
delay(5000);
}
Serial.println("AT+CCAMS"); //starts the camera
while(Serial.read()!='K');
Serial.println("AT+CCAMSETD=640,480"); //sets VGA (640*480) resolution
while(Serial.read()!='K');
Serial.println("AT+FSLOCA=0"); //stores the image file in the 3G module
while(Serial.read()!='K');
}
void loop(){
delay(1500);
while(Serial.available()!=0){
Serial.read();
}
Serial.println("AT+CCAMTP"); //takes a picture, but not saved it
while(Serial.read()!='K');
Serial.println("AT+CCAMEP"); // saves the picture into C:/Picture
Serial.flush();
while(Serial.read()!='/');
while(Serial.read()!='/');
x=0;
do{
while(Serial.available()==0);
name[x]=Serial.read();
x++;
}while(x < 19);
while(Serial.read()!='K'); Serial.println(name);
Serial.println("AT+CCAME"); // stops the camera
while(Serial.read()!='K');
while(1);
} </syntaxhighlight>
Video Call
The SIM5218 allows video calls, but to carry them out correctly the operator and the network must be able to allow it. The example code is below. Cooking Hacks not ensure that the video call functions correctly.
<syntaxhighlight lang="c"> /*
- This program is free software: you can redistribute it and/or modify
- it under the terms of the GNU General Public License as published by
- the Free Software Foundation, either version 3 of the License, or
- (at your option) any later version.
- This program is distributed in the hope that it will be useful,
- but WITHOUT ANY WARRANTY; without even the implied warranty of
- MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- GNU General Public License for more details.
- You should have received a copy of the GNU General Public License
- along with this program. If not, see .
- Version 0.1
- /
int led = 13;
int onModulePin = 2; // the pin to switch on the module (without press on button)
char phone_number[]="*********"; // ********* is the number to call
void switchModule(){
digitalWrite(onModulePin,HIGH); delay(2000); digitalWrite(onModulePin,LOW);
}
void setup(){
Serial.begin(115200); //UART baud rate delay(2000); pinMode(led, OUTPUT); pinMode(onModulePin, OUTPUT); switchModule(); // switches the module ON
for (int i=0;i< 5;i++){
delay(5000);
}
Serial.println("AT+CCAMS"); //starts the camera
while(Serial.read()!='K');
Serial.println("AT+CCAMSETD=320,240"); //sets QVGA (320*240) resolution
while(Serial.read()!='K');
Serial.println("AT+CCAMSETF=2"); //sets 15 frames per seconds
while(Serial.read()!='K');
}
void loop(){
delay(1500);
while(Serial.available()!=0){
Serial.read();
}
Serial.print("AT+VPMAKE="); //inits a videocall
Serial.println(phone_number);
delay(30000);
Serial.println("AT+VPEND"); // ends the videocall
while(Serial.read()!='K');
Serial.println("AT+CCAME"); // stops the camera
while(Serial.read()!='K');
while(1);
} </syntaxhighlight>
Command Summary
| Command | Response | Description |
|---|---|---|
| AT+CCAMS | OK | Starts camera. |
| AT+CCAME | OK | Stops camera. |
| AT+CCAMSETD=xxx,yyy | OK | Sets dimension of camera. xxx is the width and yyy is the height. |
| AT+CCAMSETF=* | OK | Sets the frames per second. * is the frame rate option. |
| AT+CCAMRS | OK | Starts video recording . Also responds with the path and name of the file. |
| AT+CCAMRP | OK | Pauses the record. |
| AT+CCAMRR | OK | Resumes video record. |
| AT+CCAMRE | OK | Stops video record. |
| AT+CCAMTP | OK | Takes a picture. |
| AT+CCAMEP | OK | Saves a picture taken by last AT+CCAMTP. Also responds with the path and name of the file. |
| AT+VPMAKE | Makes a video call. | |
| AT+VPEND | Ends a video call. |
GPS
SIM5218 supports both A-GPS and S-GPS and provides three operating modes: mobile-assisted mode, mobile-based mode and standalone mode. A-GPS is include mobile-assisted and mobile-based mode.
In mobile-assisted mode, when a request for position location is issued, available network information is provided to the location server (e.g., Cell-ID) and assistance is requested from the location server. The location server sends the assistance information to the handset. The handset/mobile unit measures the GPS observables and provides the GPS measurements along with available network data (that is appropriate for the given air interface technology) to the location server. The location server then calculates the position location and returns results to the requesting entity.
In mobile-based mode, the assistance data provided by the location server encompasses not only the information required to assist the handset in measuring the satellite signals, but also the information required to calculate the handset’s position. Therefore, rather than provide the GPS measurements and available network data back to the location server, the mobile calculates the location on the handset and passes the result to the requesting entity.
In standalone (autonomous) mode, the handset demodulates the data directly from the GPS satellites. This mode has some reduced cold-start sensitivity, and a longer time to first fix as compared to the assisted modes. However, it requires no server interaction and works out of network coverage.
This combination of GPS measurements and available network information provides:
- High-sensitivity solution that works in all terrains: indoor, outdoor, urban, and rural
- High availability that is enabled by using both satellite and network information
Therefore, while network solutions typically perform poorly in rural areas and areas of poor cell geometry/density, and while unassisted, GPS-only solutions typically perform poorly indoors, the SIM5218 GPS solution provides optimal time to fix, accuracy, sensitivity, availability, and reduced network utilization in both of these environments, depending on the given condition.
Stand-alone mode
In this mode, the GPS obtains position, altitude,... with only the signal of the satellites, making it the slowest of the three modes. If you use the AT+CGPSINFO command, the module bring directly latitud, logitude, date, UTC time, altitude and speed. Here is the example code:
<syntaxhighlight lang="c"> /*
- This program is free software: you can redistribute it and/or modify
- it under the terms of the GNU General Public License as published by
- the Free Software Foundation, either version 3 of the License, or
- (at your option) any later version.
- This program is distributed in the hope that it will be useful,
- but WITHOUT ANY WARRANTY; without even the implied warranty of
- MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- GNU General Public License for more details.
- You should have received a copy of the GNU General Public License
- along with this program. If not, see .
- Version 0.1
- /
int led = 13;
int onModulePin = 2; // the pin to switch on the module (without press on button)
char data[255]; char latitude[11],longitude[12]; char date[6],UTC_time[8]; char speed_OG[6],altitude[6];
int x,y;
void switchModule(){
digitalWrite(onModulePin,HIGH); delay(2000); digitalWrite(onModulePin,LOW);
}
void setup(){
Serial.begin(115200); // UART baud rate delay(2000); pinMode(led, OUTPUT); pinMode(onModulePin, OUTPUT); switchModule(); // switches the module ON
for (int i=0;i< 5;i++){
delay(5000);
}
Serial.println("AT+CGPS=1,1"); // starts GPS session in stand-alone mode
delay(100);
}
void loop(){
delay(5000);
Serial.println("AT+CGPSINFO"); // request GPS info
Serial.flush();
x=0;
do{
do{
digitalWrite(led,HIGH);
}
while(Serial.available()==0);
digitalWrite(led,LOW);
data[x]=Serial.read();
x++;
}
while(Serial.read()!='K');
x=24;
y=0;
if(data[x]!=','){
Serial.print("Latitude: "); //shows actual latitude
do{
latitude[y]=data[x];
Serial.print(data[x]);
y++;
x++;
}
while(data[x]!=',');
x++;
Serial.print(" ");
Serial.println(data[x]); //north or south
x+=2;
y=0;
Serial.print("Longitude: "); //shows actual longitude
do{
longitude[y]=data[x];
Serial.print(data[x]);
y++;
x++;
}
while(data[x]!=',');
x++;
Serial.print(" ");
Serial.println(data[x]); //west or east
x+=2;
y=0;
Serial.print("Date: "); //shows date
do{
date[y]=data[x];
Serial.print(data[x]);
y++;
x++;
}
while(data[x]!=',');
x++;
y=0;
Serial.print("\r\nUTC time: "); //shows UTC time
do{
UTC_time[y]=data[x];
Serial.print(data[x]);
y++;
x++;
}
while(data[x]!=',');
x++;
y=0;
Serial.print("\r\nAltitude: "); //shows altitude
do{
UTC_time[y]=data[x];
Serial.print(data[x]);
y++;
x++;
}
while(data[x]!=',');
Serial.println(" m");
x++;
y=0;
Serial.print("Speed: "); //shows speed
do{
speed_OG[y]=data[x];
Serial.print(data[x]);
y++;
x++;
}
while(data[x]!=0x0D);
Serial.println(" knots");
}
else{
Serial.println("GPS information not available, please wait...");
}
} </syntaxhighlight>
If you want to get the NMEA sentences, you must to use the command AT+CGPSSWITCH=1 and configure the UART port at 57600 bauds. Supported NMEA sentences include GSV, GGA, RMC, GSA, and VTG.
S-GPS Mode
For the S-GPS the module connects to a GPS server and the module calculates the position. Here is the example code:
<syntaxhighlight lang="c"> /*
- This program is free software: you can redistribute it and/or modify
- it under the terms of the GNU General Public License as published by
- the Free Software Foundation, either version 3 of the License, or
- (at your option) any later version.
- This program is distributed in the hope that it will be useful,
- but WITHOUT ANY WARRANTY; without even the implied warranty of
- MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- GNU General Public License for more details.
- You should have received a copy of the GNU General Public License
- along with this program. If not, see .
- Version 0.1
- /
int led = 13;
int onModulePin = 2; // the pin to switch on the module (without press on button)
char data[255]; char latitude[11],longitude[12]; char date[6],UTC_time[8]; char speed_OG[6],altitude[6];
int x,y;
void switchModule(){
digitalWrite(onModulePin,HIGH); delay(2000); digitalWrite(onModulePin,LOW);
}
void setup(){
Serial.begin(115200); // UART baud rate delay(2000); pinMode(led, OUTPUT); pinMode(onModulePin, OUTPUT); switchModule(); // switches the module ON
for (int i=0;i< 5;i++){
delay(5000);
}
Serial.println("AT+CGSOCKCONT=1,\"IP\",\"myapn\"");
Serial.flush();
x=0;
do{
while(Serial.available()==0);
response[x]=Serial.read();
x++;
}
while(!check_response("OK"));
Serial.println("AT+CGPSURL=\"supl.google.com:7276\""); // sets GPS server
delay(100);
while(Serial.read()!='K');
Serial.println("AT+CGPSSSL=0"); // without certificate
delay(100);
while(Serial.read()!='K');
Serial.println("AT+CGPS=1,2"); // starts GPS session in based mode
delay(100);
while(Serial.read()!='K');
}
void loop(){
delay(5000);
Serial.println("AT+CGPSINFO"); // request GPS info
Serial.flush();
for (x=0;x< 255;x++){
data[x]='\0';
}
x=0;
do{
do{
digitalWrite(led,HIGH);
}
while(Serial.available()==0);
digitalWrite(led,LOW);
data[x]=Serial.read();
x++;
}
while(Serial.read()!='K');
x=24;
y=0;
if(data[x]!=','){
Serial.print("Latitude: "); //shows actual latitude
do{
latitude[y]=data[x];
Serial.print(data[x]);
y++;
x++;
if(y==2){
Serial.print(0xF8);
}
if(y==4){
Serial.print(".");
}
}
while(data[x]!=',');
x++;
Serial.print(" ");
Serial.println(data[x]); //north or south
x+=2;
y=0;
Serial.print("Longitude: "); //shows actual longitude
do{
longitude[y]=data[x];
Serial.print(data[x]);
y++;
x++;
if(y==3){
Serial.print(0xF8);
}
if(y==5){
Serial.print(".");
}
}
while(data[x]!=',');
x++;
Serial.print(" ");
Serial.println(data[x]); //west or east
x+=2;
y=0;
Serial.print("Date: "); //shows date
do{
date[y]=data[x];
Serial.print(data[x]);
y++;
x++;
}
while(data[x]!=',');
x++;
y=0;
Serial.print("\r\nUTC time: "); //shows UTC time
do{
UTC_time[y]=data[x];
Serial.print(data[x]);
y++;
x++;
}
while(data[x]!=',');
x++;
y=0;
Serial.print("\r\nAltitude: "); //shows altitude
do{
UTC_time[y]=data[x];
Serial.print(data[x]);
y++;
x++;
}
while(data[x]!=',');
Serial.println(" m");
x++;
y=0;
Serial.print("Speed: "); //shows speed
do{
speed_OG[y]=data[x];
Serial.print(data[x]);
y++;
x++;
}
while(data[x]!=0x0D);
Serial.println(" knots");
}
else{
Serial.println("GPS information not available, please wait...");
}
} </syntaxhighlight>
A-GPS Mode
For the A-GPS the module connects to a GPS server for calculate the position. Here is the example code:
| MS-assisted | Server | Module |
|---|---|---|
| Location server sends aiding data that is valid for the current fix | Sending Data | |
| Module sends code phases | Code phases | |
| Server calculates position | Calculate position | |
| MS-based | Server | Module |
| Location server sends aiding data that is valid for the current fix | Send aiding data | |
| Module calculates | Calculate position | |
| Stand alone | Server | Module |
| Module demodulates data form GPS satellite | Demodulates GPS satellite data | |
| Module calculates position | Calculate position |
GPS Units
The command AT+CGPSINFO returns the GPS info in a string:
+CGPSINFO: [<latitude>],[<N/S>],[<longitude>],[<E/W>],[<date>],[<UTC_time>],[<altitude>],[<speedOG>],[<course>]
| Values | Format | Example |
|---|---|---|
| latitude | ddmm.mmmmmm / d: degree; m: minute | 4140.831527 |
| longitude | dddmm.mmmmmm / d: degree; m: minute | 00053.173495 |
| data | ddmmyy / d: day; m: month; y: year | 020812 |
| altitude | meters | 257.00 |
| speedOG | knots | 2 |
| course | degrees | 0 |
If UE-assisted mode, when fixed will report indication:
+CAGPSINFO:<latitude>,<longitude>,<altitude>,<date>,<UTC_time>
| Values | Format | Example |
|---|---|---|
| latitude | Unit is in 10^8 degree | 4168050885 |
| longitude | Unit is in 10^8 degree | 88618039 |
| altitude | meters | 293 |
| date | ddmmyyyy / d: day; m: month; y: year | 28092012 |
| UTC_time | hhmmss.s / h: hour; m: minute; s: seconds | 081611.0 |
Command Summary
| Command | Response | Description |
|---|---|---|
| AT+CGSOCKCONT=**,&&& | OK | ** is the protocol and &&& Access Point Name. |
| AT+CGPS=*,& | OK | * sets on (1) or off (0) and & is the GPS mode. |
| AT+CGPSINFO | Gets current position information. | |
| AT+CGPSURL=”***” | OK | Sets AGPS default server URL . *** is the URL. |
| AT+CGPSSSL=* | OK | Select transport security, used certificate (*=1) or not (*=0). |
| AT+CGPSSWITCH | OK | Choose the output port for NMEA sentence. |
SMS
Sending and Receiving SMS
The first code is used to send a SMS, the second one reads the SIM message memory and shows the last SMS.
<syntaxhighlight lang="c"> /*
- This program is free software: you can redistribute it and/or modify
- it under the terms of the GNU General Public License as published by
- the Free Software Foundation, either version 3 of the License, or
- (at your option) any later version.
- This program is distributed in the hope that it will be useful,
- but WITHOUT ANY WARRANTY; without even the implied warranty of
- MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- GNU General Public License for more details.
- You should have received a copy of the GNU General Public License
- along with this program. If not, see .
- Version 0.1
- /
int led = 13;
int onModulePin = 2; // the pin to switch on the module (without press on button)
int timesToSend = 1; // Numbers of SMS to send int count = 0;
char phone_number[]="*********"; // ********* is the number to call
void switchModule(){
digitalWrite(onModulePin,HIGH); delay(2000); digitalWrite(onModulePin,LOW);
}
void setup(){
Serial.begin(115200); // UART baud rate delay(2000); pinMode(led, OUTPUT); pinMode(onModulePin, OUTPUT); switchModule(); // switches the module ON
for (int i=0;i< 5;i++){
delay(5000);
}
Serial.println("AT+CMGF=1"); // sets the SMS mode to text
delay(100);
}
void loop(){
while (count < timesToSend){
delay(1500);
Serial.print("AT+CMGS=\""); // send the SMS number
Serial.print(phone_number);
Serial.println("\"");
delay(1500);
Serial.print("Hola caracola..."); // the SMS body
delay(500);
Serial.write(0x1A); //sends ++
Serial.write(0x0D);
Serial.write(0x0A);
delay(5000);
count++; }
} </syntaxhighlight>
another code <syntaxhighlight lang="c">
* This program is free software: you can redistribute it and/or modify * it under the terms of the GNU General Public License as published by * the Free Software Foundation, either version 3 of the License, or * (at your option) any later version. * * This program is distributed in the hope that it will be useful, * but WITHOUT ANY WARRANTY; without even the implied warranty of * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the * GNU General Public License for more details. * * You should have received a copy of the GNU General Public License * along with this program. If not, see http://www.gnu.org/licenses/. * * Version 0.1 */
int led = 13;
int onModulePin = 2; // the pin to switch on the module (without press on button)
int timesToSend = 1; // Numbers of SMS to send int count = 0;
int n_sms,x,sms_start; char data[256];
void switchModule(){
digitalWrite(onModulePin,HIGH); delay(2000); digitalWrite(onModulePin,LOW);
}
void setup(){
Serial.begin(115200); // UART baud rate delay(2000); pinMode(led, OUTPUT); pinMode(onModulePin, OUTPUT); switchModule(); // switches the module ON
for (int i = 0;i < 5;i++){
delay(5000);
}
Serial.println("AT+CMGF=1"); // sets the SMS mode to text
delay(100);
x = 0;
do{
while(Serial.available()==0);
data[x]=Serial.read();
x++;
} while(!((data[x-1] == 'K') && (data[x-2] == 'O')));
}
void loop(){
while (count < timesToSend){
delay(1500);
while(Serial.available()!=0) Serial.read();
Serial.println("AT+CPMS=\"SM\",\"SM\",\"SM\""); //selects SIM memory
Serial.flush();
for (x=0;x < 255;x++){
data[x]='\0';
}
x=0;
do{
while(Serial.available()==0);
data[x]=Serial.read();
x++;
}while(!((data[x-1] == 'K') && (data[x-2] == 'O')));
x=0;
do{
x++;
}while (data[x] != ' ');
x++;
n_sms=0;
do{
n_sms*=10;
n_sms=n_sms + (data[x]-0x30);
x++;
}while (data[x] != ',');
Serial.print(" ");
Serial.print(n_sms,DEC);
// Now it shows the total number of SMS and the last SMS
Serial.println(" SMS stored in SIM memory. Showing last SMS:");
Serial.print("AT+CMGR="); //Reads the last SMS
Serial.println(n_sms-1,DEC);
Serial.flush();
for (x=0;x < 255;x++){
data[x]='\0';
}
x=0;
do{
while(Serial.available()==0);
data[x]=Serial.read();
x++;
if((data[x-1] == 0x0D) && (data[x-2] == '"')){
x=0;
}
}
while(!((data[x-1] == 'K') && (data[x-2] == 'O')));
data[x-3]='\0'; //finish the string before the OK
Serial.println(data); //shows the message
delay(5000);
count++; }
} </syntaxhighlight>
Command Summary
| Command | Response | Description |
|---|---|---|
| AT+CMGF= | OK | Specifies the input and output format of the short messages. 0 for PDU mode and 1 for text mode. |
| AT+CMGS | Sends a message. | |
| AT+CPMS=*** | Selects memory storages. *** is the memory type. | |
| AT+CMGR=* | Reads a message. * is the number of the message. |
E-mails
Sending an E-mail
To send e-mail a SMTP server is used, so we need an e-mail account. The code example is the next:
<syntaxhighlight lang="c"> /*
- This program is free software: you can redistribute it and/or modify
- it under the terms of the GNU General Public License as published by
- the Free Software Foundation, either version 3 of the License, or
- (at your option) any later version.
- This program is distributed in the hope that it will be useful,
- but WITHOUT ANY WARRANTY; without even the implied warranty of
- MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- GNU General Public License for more details.
- You should have received a copy of the GNU General Public License
- along with this program. If not, see .
- Version 0.1
- /
int led = 13;
int onModulePin = 2; // the pin to switch on the module (without press on button)
int x;
//server and account data char server[ ]=""; char user_name[ ]=""; char password[ ]=""; char port[ ]="";
//information about sender, direcctions and names char sender_add[ ]=""; char sender_name[ ]="";
char to_add[ ]=""; char to_name[ ]="";
char cc_add[ ]=""; char cc_name[ ]="";
char bcc_add[ ]=""; char bcc_name[ ]="";
// char subject[ ]=""; char body[ ]="";
char response[128];
void switchModule(){
digitalWrite(onModulePin,HIGH); delay(2000); digitalWrite(onModulePin,LOW);
}
void setup(){
Serial.begin(115200); // UART baud rate delay(2000); pinMode(led, OUTPUT); pinMode(onModulePin, OUTPUT); switchModule(); // switches the module ON
for (int i=0;i< 5;i++){
delay(5000);
}
}
void loop(){
Serial.print("AT+SMTPSRV=\"");
//configures the SIM5218 with server name and port
Serial.print(server);
Serial.print("\",");
Serial.println(port);
Serial.flush();
x=0;
do{
while(Serial.available()==0);
response[x]=Serial.read();
x++;
}
while(!(response[x-1]=='K'&&response[x-2]=='O'));
Serial.print("AT+SMTPAUTH=1,\""); //configures the SIM5218 with user name and password
Serial.print(user_name);
Serial.print("\",\"");
Serial.print(password);
Serial.println("\"");
Serial.flush();
x=0;
do{
while(Serial.available()==0);
response[x]=Serial.read();
x++;
}
while(!(response[x-1]=='K'&&response[x-2]=='O'));
Serial.print("AT+SMTPFROM=\""); //sender adress and name
Serial.print(sender_add);
Serial.print("\",\"");
Serial.print(sender_name);
Serial.println("\"");
Serial.flush();
x=0;
do{
while(Serial.available()==0);
response[x]=Serial.read();
x++;
}
while(!(response[x-1]=='K'&&response[x-2]=='O'));
Serial.print("AT+SMTPRCPT=0,0,\""); //normal recipient address and name
Serial.print(to_add);
Serial.print("\",\"");
Serial.print(to_name);
Serial.println("\"");
Serial.flush();
x=0;
do{
while(Serial.available()==0);
response[x]=Serial.read();
x++;
}
while(!(response[x-1]=='K'&&response[x-2]=='O'));
//If you don't need a carbon copy, delete this part
Serial.print("AT+SMTPRCPT=1,0,\""); //carbon copy recipient address and name
Serial.print(cc_add);
Serial.print("\",\"");
Serial.print(cc_name);
Serial.println("\"");
Serial.flush();
x=0;
do{
while(Serial.available()==0);
response[x]=Serial.read();
x++;
}
while(!(response[x-1]=='K'&&response[x-2]=='O'));
//If you don't need a blind carbon copy, delete this part
Serial.print("AT+SMTPRCPT=2,0,\""); //blind carbon copy recipient address and name
Serial.print(bcc_add);
Serial.print("\",\"");
Serial.print(bcc_name);
Serial.println("\"");
Serial.flush();
x=0;
do{
while(Serial.available()==0);
response[x]=Serial.read();
x++;
}
while(!(response[x-1]=='K'&&response[x-2]=='O'));
Serial.print("AT+SMTPSUB=\""); //subjec of email
Serial.print(subject);
Serial.println("\"");
Serial.flush();
x=0;
do{
while(Serial.available()==0);
response[x]=Serial.read();
x++;
}
while(!(response[x-1]=='K'&&response[x-2]=='O'));
Serial.print("AT+SMTPBODY=\""); //body of email
Serial.print(body);
Serial.println("\"");
Serial.flush();
x=0;
do{
while(Serial.available()==0);
response[x]=Serial.read();
x++;
}
while(!(response[x-1]=='K'&&response[x-2]=='O'));
Serial.println("AT+CGSOCKCONT=1,\"IP\",\"myapn\"");
Serial.flush();
x=0;
do{
while(Serial.available()==0);
response[x]=Serial.read();
x++;
}
while(!(response[x-1]=='K'&&response[x-2]=='O'));
Serial.println("AT+SMTPSEND"); //sends the email
Serial.flush();
x=0;
do{
while(Serial.available()==0);
response[x]=Serial.read();
x++;
}
while(!(response[x-1]=='K'&&response[x-2]=='O'));
Serial.print("Sending email...");
x=0;
do{
do{
digitalWrite(led,HIGH);
}
while(Serial.available()==0);
digitalWrite(led,LOW);
response[x]=Serial.read();
x++;
}
while(!(response[x-1]=='S'&&response[x-2]=='S'));
Serial.println(response);
while(1);
} </syntaxhighlight>
Receiving an E-mail
For read an e-mail from a POP3 server we need an e-mail account. The code example is here: <syntaxhighlight lang="c"> /*
- This program is free software: you can redistribute it and/or modify
- it under the terms of the GNU General Public License as published by
- the Free Software Foundation, either version 3 of the License, or
- (at your option) any later version.
- This program is distributed in the hope that it will be useful,
- but WITHOUT ANY WARRANTY; without even the implied warranty of
- MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- GNU General Public License for more details.
- You should have received a copy of the GNU General Public License
- along with this program. If not, see .
- Version 0.1
- /
int led = 13;
int onModulePin = 2; // the pin to switch on the module (without press on button)
int x;
//server and account data char server[ ]=""; char user_name[ ]=""; char password[ ]=""; char port[ ]="";
char data[1024];
char path[50];
void switchModule(){
digitalWrite(onModulePin,HIGH); delay(2000); digitalWrite(onModulePin,LOW);
}
void setup(){
Serial.begin(115200); // UART baud rate delay(2000); pinMode(led, OUTPUT); pinMode(onModulePin, OUTPUT); switchModule(); // switches the module ON
for (int i=0;i< 5;i++){
delay(5000);
}
Serial.println("AT+CGSOCKCONT=1,\"IP\",\"myapn\"");
Serial.flush();
x=0;
do{
while(Serial.available()==0);
data[x]=Serial.read();
x++;
}while(!(data[x-1]=='K'&&data[x-2]=='O'));
}
void loop(){
Serial.print("AT+POP3SRV=\"");
//configures the SIM5218 with server name, user, password and port
Serial.print(server);
Serial.print("\",\"");
Serial.print(user_name);
Serial.print("\",\"");
Serial.print(password);
Serial.print("\",");
Serial.println(port);
Serial.flush();
x=0;
do{
while(Serial.available()==0);
data[x]=Serial.read();
x++;
}
while(!(data[x-1]=='K'&&data[x-2]=='O'));
Serial.println("AT+POP3IN"); //logs into the server
Serial.flush();
x=0;
do{
while(Serial.available()==0);
data[x]=Serial.read();
x++;
}while(!(data[x-1]=='K'&&data[x-2]=='O'));
Serial.println("AT+POP3GET=1"); //gets the first email
Serial.flush();
do{
while(Serial.available()==0);
path[0]=Serial.read();
}while(path[0]!='/');
do{
while(Serial.available()==0);
path[0]=Serial.read();
}
while(path[0]!='/');
x=0;
do{
while(Serial.available()==0);
path[x]=Serial.read();
x++;
}while(path[x-1]!=' ');
x--; //overwrite " " charracter x--; //overwrite "," charracter
do{
while(Serial.available()==0);
path[x]=Serial.read();
x++;
}while(path[x-1]!=0x0D);
path[x-1]='\0';
Serial.println("AT+POP3OUT"); //logs out the server
Serial.flush();
x=0;
do{
while(Serial.available()==0);
data[x]=Serial.read();
x++;
}while(!(data[x-1]=='K'&&data[x-2]=='O'));
Serial.println("AT+FSCD=C:/Email"); //selects email directory as current directory
Serial.flush();
x=0;
do{
while(Serial.available()==0);
data[x]=Serial.read();
x++;
}while(!(data[x-1]=='K'&&data[x-2]=='O'));
Serial.print("AT+POP3READ=0,\""); //shows the email
Serial.print(path);
Serial.println("\"");
Serial.flush();
do{
while(Serial.available()==0);
data[0]=Serial.read();
}while(data[0]!='D');
do{
while(Serial.available()==0);
data[0]=Serial.read();
}while(data[0]!='D');
x=1;
do{
while(Serial.available()==0);
data[x]=Serial.read();
x++;
if(x==1020){
Serial.print(data);
x=0;
}
}while(!(data[x-1]=='K'&&data[x-2]=='O'&&data[x-3]==0x0A&&data[x-4]==0x0D));
data[x-2]='\0'; Serial.println(data); while(1);
} </syntaxhighlight>
Command Summary
| Command | Response | Description |
|---|---|---|
| AT+CGSOCKCONT=**,&&& | OK | ** is the protocol and &&& Access Point Name. |
| AT+SMTPSRV=”*****”,&&& | OK | Sets SMTP server address and server’s port . ***** is the sever address and &&& is the server's port. |
| AT+SMTPAUTH=1,”***”,”&&&” | OK | Controls SMTP authentication. *** is the user name and &&& is the password. |
| AT+SMTPFROM=”***”,”&&&” | OK | Sets sender’s address and nam e. *** is the sender's address and &&& is the sender's name. |
| AT+SMTPRCPT=x,”***”,”&&&” | OK | Sets recipient address/name and kind . x is the kind (TO/CC/BCC), *** is the recipient address and &&& is the recipient name. |
| AT+SMTPSUB=”****” | OK | Sets the subject of e-mail . **** is the subject. |
| AT+SMTPBODY | Sets e-mail body. | |
| AT+SMTPSEND | Initiates TCP session with SMTP server and sends an e-mail | |
| AT+POP3SRV=”**”,”&&”,”xx”,yy | OK | Sets all parameters to get an e-mail from POP3 . ** is the server address, && is the user name, xx is the password and yy the server port |
| AT+POP3IN | OK | Logs in POP3 server |
| AT+POP3GET=*** | Gets an e-mail from POP3 server , *** is the number of the e-mail. | |
| AT+POP3OUT | OK | Logs out POP3 server |
| AT+POP3READ=”***”,”&&&” | Reads an e-mail from file system . *** is the location and &&& is the name. |
