Difference between revisions of "Acrylic Turtle 2WD Mobile Video Robot powered by pcDuino2"
Qian.zhang (talk | contribs) (Created page with "== Introduction == The new robot with acrylic frame and video surveillance, it uses pcDuino V2 as control board. File:pcDuino V2 acrylic robot.jpg [[File:pcDuino V2 acr...") |
Qian.zhang (talk | contribs) (→Introduction) |
||
| (5 intermediate revisions by the same user not shown) | |||
| Line 3: | Line 3: | ||
The new robot with acrylic frame and video surveillance, it uses pcDuino V2 as control board. | The new robot with acrylic frame and video surveillance, it uses pcDuino V2 as control board. | ||
| − | [[File:pcDuino V2 acrylic | + | [[File:pcDuino V2 acrylic robot_1.jpg]] |
[[File:pcDuino V2 acrylic robot list.jpg]] | [[File:pcDuino V2 acrylic robot list.jpg]] | ||
| Line 11: | Line 11: | ||
*1 × [http://www.pcduino.com/pcduino-v2/ pcDuino V2][MP_PCDUINOV2][102102006] | *1 × [http://www.pcduino.com/pcduino-v2/ pcDuino V2][MP_PCDUINOV2][102102006] | ||
| − | *1 × [http://linksprite.com/wiki/index.php5?title= | + | *1 × [http://linksprite.com/wiki/index.php5?title=Mini_Webcam_for_Robot_Video_Real_Time_Video_Stream Mini Webcam for Robot Video Real Time Video Stream][WEBCAM_PCDUINO][108202004-1] |
*1 × [http://linksprite.com/wiki/index.php5?title=Motor_Shield Motor Shield][SHD_MOTOR][101101014][SHD_MOTOR][101101014] | *1 × [http://linksprite.com/wiki/index.php5?title=Motor_Shield Motor Shield][SHD_MOTOR][101101014][SHD_MOTOR][101101014] | ||
| Line 34: | Line 34: | ||
== Assembly Instruction == | == Assembly Instruction == | ||
| − | *[http:// | + | == Assembly Instruction == |
| + | *For the frame of robot assembly instruction, please refer to here: http://linksprite.com/wiki/index.php5?title=Acrylic_Frame_Robot_Platform#Assembly_Instructions | ||
| + | |||
| + | ===Firmware of pcDuino2=== | ||
| + | *Write Kernel: | ||
| + | **Use [https://s3.amazonaws.com/pcduino/Tools/PhoenixCardV306_20120302.rar PhoenixCard.exe] write [http://pan.baidu.com/s/1bnqz4hp pcduino_a10_kernel_livesuit_20140504.img] to a SD card. | ||
| + | |||
| + | [[File:write kernel_v2_1.jpg]] | ||
| + | |||
| + | **Insert the SD card to pcDuino2 and power on. You will find the Tx LED on pcDuino2 blink. Wait a moment , the Tx LED will stop blink, this indicates that the kernel is write to pcDuino2, power off pcDuino2 and take out the SD card. | ||
| + | |||
| + | [[File:write kernel_v2_2.jpg]] | ||
| + | |||
| + | *Write Firmware: | ||
| + | **Format the last step's SD card， copy the [http://pan.baidu.com/s/1bnqz4hp image] to the SD card. | ||
| + | |||
| + | [[File:write firmware_v2.jpg]] | ||
| + | |||
| + | **Connect pcDuino2 with HDMI screen and power on it, when you see: | ||
| + | |||
| + | searching update.sh from usb disk | ||
| + | searching update.sh from sdcard | ||
| + | |||
| + | Insert the SD card to pcDuino2, you will see: | ||
| + | |||
| + | it will take about 10 minutes to finish… | ||
| + | |||
| + | Then wait servel minutes, the screen will remind you update finished. | ||
| + | |||
| + | ===Install pcDuino2 On The Robot=== | ||
| + | |||
| + | *Refer to [http://linksprite.com/wiki/index.php5?title=Acrylic_Frame_Robot_Platform#Assembly_Instructions Explanation of Acrylic Top Plate], use screws and nuts fix the pcDuino2 on acrylic top plate: | ||
| + | |||
| + | [[File:install v2_1.jpg]] | ||
| + | |||
| + | [[File:install v2_2.jpg]] | ||
| + | |||
| + | *Add Motor Shield on pcDuino2, put batterys in ,connect the Motors' control and power wires. Plug the USB of mini webcam to pcDuino2. Here we powered on pcDuino2 with 5V/2A mobile power supply： | ||
| + | |||
| + | [[File:add motor.jpg]] | ||
| + | |||
| + | *Wait the Rx and Tx LEDs on pcDuino2 light up, this indicates that pcDuino2 is set up. Open WLAN of your Android cellphone, you will find a net named "carwifi", join it, the password is "12345678". | ||
| + | |||
| + | ===App of Android=== | ||
| + | |||
| + | *Install the [http://pan.baidu.com/s/1bny7pmf WiFiRobot.apk] on your Android cellphone and open it. Click your cellphone's menu key, you will see the following picture: | ||
| + | |||
| + | [[File:apk_1.jpg]] | ||
| + | |||
| + | *Click "Setting" , set IP as the following picture: | ||
| + | |||
| + | [[File:apk_2.jpg]] | ||
| + | |||
| + | *Click "save" to save the settings. Then click "START", you will see "socket link success" and "video link success", your cellphone display the monitor screen before the mini webcam. | ||
| + | |||
| + | [[File:apk_3.jpg]] | ||
| + | |||
| + | *Now you can control your robot with Fore, Back, Left, Right button on the lower right corner. | ||
| + | You may find the robot's action is not right as the suppose， this is because the Motors' control wires are not at right position, you can exchange them. | ||
== Resources == | == Resources == | ||
*[https://s3.amazonaws.com/linksprite/robot/pcDuino+V2+video+robot/pcduino_car_with_video_9V_20140509.7z Firmware of pcDuino V2(Green WiFi Module)] | *[https://s3.amazonaws.com/linksprite/robot/pcDuino+V2+video+robot/pcduino_car_with_video_9V_20140509.7z Firmware of pcDuino V2(Green WiFi Module)] | ||
*[https://s3.amazonaws.com/linksprite/robot/pcDuino+V2+video+robot/WiFiRobot.apk WiFiRobot.apk] | *[https://s3.amazonaws.com/linksprite/robot/pcDuino+V2+video+robot/WiFiRobot.apk WiFiRobot.apk] | ||
Latest revision as of 07:23, 2 February 2015
Contents
Introduction
The new robot with acrylic frame and video surveillance, it uses pcDuino V2 as control board.
File:PcDuino V2 acrylic robot 1.jpg
Package List
- 1 × pcDuino V2[MP_PCDUINOV2][102102006]
- 1 × Mini Webcam for Robot Video Real Time Video Stream[WEBCAM_PCDUINO][108202004-1]
- 1 × Motor Shield[SHD_MOTOR][101101014][SHD_MOTOR][101101014]
- 1 × Acrylic Frame Robot Platform [KIT_ROT_T2WDACY][108301011]
- 1 × Wall Power Adapter (5V 2A)[POW_5V2AUSB_EU][126201003]
- 1 × Micro USB cable[CAB_uB][117201004]
- 1 × 4 port USB hub[TOL-USBHUB-4PT][125201004]
- 1 × HDMI cable[CAB_HDMI][117201007]
- 1 × Clear Case V2
- 1 × LinkSprite Clear Enclosure for pcDuino[COM_CASE_PCDUINO_CLEAR] [114201005]
- 1 × Acrylic Baffle Plate for pcDuino V2[CASE_PCDV2END][128201001]
- 1 × Plate of Case[COM_CASE_ARDU_CLEAR_PLATE][114201003]
- 10× 2.54mm to 2.0mm Jumper Wire[IT_JUMR_FF2.54_2.0MM_WI20CM][BB101101]
Assembly Instruction
Assembly Instruction
- For the frame of robot assembly instruction, please refer to here: http://linksprite.com/wiki/index.php5?title=Acrylic_Frame_Robot_Platform#Assembly_Instructions
Firmware of pcDuino2
- Write Kernel:
- Use PhoenixCard.exe write pcduino_a10_kernel_livesuit_20140504.img to a SD card.
- Insert the SD card to pcDuino2 and power on. You will find the Tx LED on pcDuino2 blink. Wait a moment , the Tx LED will stop blink, this indicates that the kernel is write to pcDuino2, power off pcDuino2 and take out the SD card.
- Write Firmware:
- Format the last step's SD card， copy the image to the SD card.
- Connect pcDuino2 with HDMI screen and power on it, when you see:
searching update.sh from usb disk searching update.sh from sdcard
Insert the SD card to pcDuino2, you will see:
it will take about 10 minutes to finish…
Then wait servel minutes, the screen will remind you update finished.
Install pcDuino2 On The Robot
- Refer to Explanation of Acrylic Top Plate, use screws and nuts fix the pcDuino2 on acrylic top plate:
- Add Motor Shield on pcDuino2, put batterys in ,connect the Motors' control and power wires. Plug the USB of mini webcam to pcDuino2. Here we powered on pcDuino2 with 5V/2A mobile power supply：
- Wait the Rx and Tx LEDs on pcDuino2 light up, this indicates that pcDuino2 is set up. Open WLAN of your Android cellphone, you will find a net named "carwifi", join it, the password is "12345678".
App of Android
- Install the WiFiRobot.apk on your Android cellphone and open it. Click your cellphone's menu key, you will see the following picture:
- Click "Setting" , set IP as the following picture:
- Click "save" to save the settings. Then click "START", you will see "socket link success" and "video link success", your cellphone display the monitor screen before the mini webcam.
- Now you can control your robot with Fore, Back, Left, Right button on the lower right corner.
You may find the robot's action is not right as the suppose， this is because the Motors' control wires are not at right position, you can exchange them.
