Difference between revisions of "Linker Zigbee Gateway Module"

From LinkSprite Playgound
Jump to: navigation, search
(Steps)
(Steps)
 
(2 intermediate revisions by the same user not shown)
Line 45: Line 45:
 
'''1. Register and login''' [http://www.linksprite.com/ '''www.linksprite.com''']   
 
'''1. Register and login''' [http://www.linksprite.com/ '''www.linksprite.com''']   
  
Go to www.linksprite.io, create an account if you don’t have one, and login, create a DIY device. The type is '''00(Custom device type)'''. The device name and device group can be arbitrary. The following summarizes:
+
Go to [http://www.linksprite.io/ www.linksprite.io], create an account if you don’t have one, and login, create a DIY device. The type is '''00(Custom device type)'''. The device name and device group can be arbitrary. The following summarizes:
  
 
*Go to [http://www.linksprite.io/ '''www.linksprite.io''']
 
*Go to [http://www.linksprite.io/ '''www.linksprite.io''']
Line 85: Line 85:
  
  
Note: You have to install [https://github.com/YaoQ/zigbee/blob/master/pyserial pyserial] in the system.
+
'''Note:''' You have to install [https://pypi.python.org/pypi/pyserial/ pyserial]in the system.
  
4. Add the first device
+
'''4. Add the first device'''
  
 
*Run the ZigBee.py program
 
*Run the ZigBee.py program

Latest revision as of 06:35, 4 July 2016

Introduction

118101035-new-1.jpg

118101035-new-2.jpg


Linker ZigBee gateway module is one kind of Linker modules which can communicate with up to 32 ZigBee node devices. It is powered by Marvell 88MZ100 ZigBee microcontroller SoC chip. This ZigBee offers advantages for many application scenarios, including lighting control, smart metering, home/building automation, remote controls and health care applications.


Features

  • Marvell MZ100 ZigBee SoC chip
    • A ZigBee compliant platform and IEEE802.15.4-2003/2006 transceiver
    • 32 bit ARM Cortex M3 microcontroller running at 32 or 64 MHz with Marvell’s proven peripheral IPs
    • On-chip DC-DC converter that can directly take input range from 2 volt to 3.6 volt
  • UART serial communication protocol
  • Linker port with 4 pins
  • 3.3V


Tutorial

we will show how to interface Deepcam ZigBee sensors to LinkSpriteIO using the Linker ZigBee gateway, and serves as a basic framework for home automation sensors application.


Prerequisites

pcDuino3B or pcDuino8 Uno X1

ZigBee Gateway module X1

Linker Button X1

Linker Base shield X1

ZigBee water leaking detector X1


For simplicity, this tutorial uses only one ZigBee sensor: ZigBee water leak detector.

Steps

1. Register and login www.linksprite.com

Go to www.linksprite.io, create an account if you don’t have one, and login, create a DIY device. The type is 00(Custom device type). The device name and device group can be arbitrary. The following summarizes:

  • Go to www.linksprite.io
  • Create an account and login
  • Create a device with type 00, and arbitrary device name and group name.

118101035-instruction-1.png


  • Obtain deviceID

118101035-instruction-2.png

  • Obtain apikey

118101035-instruction-3.png


2. Hardware connection

According to the following diagram to connect pcDuino3B, ZigBee gateway and other equipment.

118101035-instruction-4.png


3. Download the ZigBee gateway demo code

Turn on pcDuino3B, open a terminal and download the zigBee gateway code from the github. We also need to modify the deviceID and apikey with yours, run the code and add a ZigBee device.

  • Download source files
  git clone https://github.com/YaoQ/zigbee.git
  • Modify apikey and deviceID using the ones obtained above.
   cd zigbee           
   vim zigbee.py  

118101035-instruction-5.png


Note: You have to install pyserialin the system.

4. Add the first device

  • Run the ZigBee.py program
python zigbee.py   


118101035-instruction-6.png

Press and hold the RST pin hole of the water sensor until the green LED blink fast. Now we can start to add device by pressing the linker button:

118101035-instruction-7.png


118101035-instruction-8.png

Till now, we added water detector successfully to the ZigBee gateway. Now we can observe the status of the water detector on www.linksprite.io web portal. Water detector is a water leakage detector, when we place it on the place that has water, we can see status change on the web portal.

118101035-instruction-9.png

5. How to add more ZigBee devices

Follow the steps above, we have been able to add a device, and we continue to add other devices. In the case of ZigBee.py program:

  • Press and hold the reset for several seconds, the sensor's Green LED flashing rapidly, enter the reset State
  • Press Linker button add equipment,wait for complete
  • When you are finished adding the device, get the zone type information, equipment added
  • At this point, the gateway can already get sensor alarm information, and can be uploaded to the LinkSprite.io

More sensors can be found at here.