Difference between revisions of "Tilt Module"

From LinkSprite Playgound
Jump to: navigation, search
(Introduction)
 
(12 intermediate revisions by 2 users not shown)
Line 1: Line 1:
[[File:Linker tilt2.jpg |400px]]
+
==Introduction==
 +
The Linker Tilt Module is the equivalent of a button, and is used as a digital input. Inside the tilt switch is a pair of balls that make contact with the pins when the case is upright. Tilt the case over and the balls don't touch, thus not making a connection. It is wired to the SIG line, NC is not used on this kit.
  
== Sample ==
+
[[File:Tilt 118101004 first.jpg| 500px]]
 +
 
 +
[[File:Tilt 118101004 second.jpg| 500px]]
 +
 
 +
[[File:Tilt 118101004 third.jpg| 500px]]
 +
 
 +
== Features ==
 +
 
 +
Dimensions: 27.9×25.4×10.6mm
 +
 
 +
Net weight: 3.6g
 +
 
 +
== Dimension ==
 +
 
 +
[[File:tilt dimension.jpg]]
 +
 
 +
== Schematics ==
 +
*[https://s3.amazonaws.com/linksprite/LinkerKit/Linker+Tilt.pdf Schematics]
 +
 
 +
==Application Ideas==
  
 
<syntaxhighlight lang="c">
 
<syntaxhighlight lang="c">
  
const int ButtonPin=9;
+
int ledPin = 13;
void setup() {
+
int switchPin = 7;
   pinMode(ButtonPin, INPUT);
+
int val = 0;
   Serial.begin(9600);       // init serial to 9600b/s
+
void setup()
 +
{
 +
   pinMode(ledPin,OUTPUT);
 +
   pinMode(switchPin,INPUT);
 +
}
 +
void loop()
 +
{
 +
  //digitlRead(switchPin,HIGH)
 +
  val = digitalRead(switchPin);
 +
  if (HIGH == val)  digitalWrite(ledPin,HIGH);
 +
  else  digitalWrite(ledPin,LOW);
 
}
 
}
 
void loop() {
 
  int sensorValue = digitalRead(ButtonPin);
 
  if(sensorValue==1)
 
  {
 
    Serial.println("Hign");   
 
  }
 
  else
 
  {
 
    Serial.println("Low");   
 
   
 
  }
 
}
 
  
  
 
</syntaxhighlight>
 
</syntaxhighlight>
  
== Schematics ==
+
[[File:Tilt link.jpg]]
*[https://s3.amazonaws.com/linksprite/LinkerKit/Linker+Tilt.pdf Schematics]
+
 
 +
==How to buy==
 +
Here to buy Tilt Module on [http://store.linksprite.com/tilt-module-of-linker-kit-for-pcduino-arduino/ store]

Latest revision as of 08:17, 14 September 2016

Introduction

The Linker Tilt Module is the equivalent of a button, and is used as a digital input. Inside the tilt switch is a pair of balls that make contact with the pins when the case is upright. Tilt the case over and the balls don't touch, thus not making a connection. It is wired to the SIG line, NC is not used on this kit.

Tilt 118101004 first.jpg

Tilt 118101004 second.jpg

Tilt 118101004 third.jpg

Features

Dimensions: 27.9×25.4×10.6mm

Net weight: 3.6g

Dimension

Tilt dimension.jpg

Schematics

Application Ideas

<syntaxhighlight lang="c">

int ledPin = 13; int switchPin = 7; int val = 0; void setup() {

 pinMode(ledPin,OUTPUT);
 pinMode(switchPin,INPUT);

} void loop() {

 //digitlRead(switchPin,HIGH)
 val = digitalRead(switchPin);
 if (HIGH == val)  digitalWrite(ledPin,HIGH);
 else  digitalWrite(ledPin,LOW);

}


</syntaxhighlight>

Tilt link.jpg

How to buy

Here to buy Tilt Module on store